Miscellaneous Options - Viking C-200 Technical Practice

Setting C - Silence Time Out
This feature selects the length of time that calls will remain connected without voice activity.
Programmable in increments of 10 seconds up to a maximum of 90 seconds (Touch Tones
1 - 9). To disable the silence time out, program 0 in this location. Use chart at the right.
* Note: The factory default is 40 seconds.
Setting D - Dial Next Number on Ring No Answer
If enabled and a ring-no-answer is detected, the E-35
phone will dial the next programmed speed dial num-
ber, and continue to cycle through the emergency
numbers until a call is completed. * Note: This feature is disabled in the factory default.
Setting E - Dial Next Number on Busy
If enabled and a busy is detected, the E-35 phone will dial the next programmed
speed dial number, and continue to cycle through the emergency numbers until a
call is completed. * Notes: This feature is disabled in the factory default setting. If
the busy signal is interrupted with a promotional message, contact your central
office to have it removed.
Setting F - Pulse Dialing Rate (Pulses per Second)
The E-35 phone is capable of different pulse dialing speeds. * Note: The factory
default setting is 10pps (pulses per second).
F. Miscellaneous Options
Factory Default Setting: 0 + 0 + 0 + 2 + 1 + 0
Not Applicable (enter 0)
Hang-up on Return to Dial Tone
Panasonic Mode
Lap Counter
Settings A / B / C - Not Applicable
Setting D - Hang Up on Return to Dial Tone
If enabled and a return dial tone is detected, the E-35 will hang up.
* Note: The factory default setting is enabled.
Setting E - Panasonic Mode
The E-35 can be programmed to recognize the double ring cadence that is typical of
Panasonic phone systems. If the E-35 is connected to a Panasonic extension, (or any other
system that provides a double ring cadence) enable "Panasonic Mode" will allow for proper
call progress detection.
* Note: This feature is disabled in the factory default setting.
Setting F - Lap Counter
With the lap counter disabled (factory setting), if the E-35 is programmed to dial
the next number on ring-no-answer and/or busy signal (see page 6 and 7), the
E-35 will continuously call its programmed phone numbers forever until the call
is answered.
The lap counter is a programmable counter that determines how many times the E-35 will cycle through its list of up to 5 emer-
gency number (or up to 3 "Info" phone numbers), before it stops the dialing process and hangs up. When all of the programmed
phone numbers have been dialed, the lap counter is incremented and the dialing process repeats. When the lap counter has
been met, the dialing process stops and the E-30 hangs up. * Note: This feature is disabled in the factory default setting.
(memory location #17)
Dial: A + B + C + D + E + F + # + 1 + 7
Touch Tone Setting D
1 or 0 Disabled*
2, 3, 4...9 Dials second number after
2, 3, 4...9 rings respectively
A
0
Touch Tone
0
1-9
Touch Silence
Tone Time Out
0 Disabled
1 10 sec
2 20 sec
3 30 sec
4 40 sec*
5 50 sec
6 60 sec
7 70 sec
8 80 sec
9 90 sec
Touch Tone Setting E
1 Disabled*
2 Enabled
Touch Tone Setting F
1 10 pps*
2 20 pps
Enter Settings Here:
B C D E F
0 0 #17
Touch Tone Setting D
1 Disabled
2 Enabled*
Touch Tone Setting E
1 Disabled*
2 Enabled
Setting F
Disabled*
Lap count = 1-9 times
7