Summary of Contents for Argos Scandinavia 4 door robe w/ 2+4 drws.
Page 1
Scandinavia 4 door robe w/ 2+4 drws. 530mm 1404mm 1799mm Page 1 of 25 Scandinavia 4 door robe w/ 2+4 drws.
Page 2
Please sort out all parts before you begin to assemble the item. This to make sure you always use the correct part. Fittings contained in the Box. 22 pcs. 42 pcs. Bolt - ø6,5 x 24/11mm 24 pcs. ø15 x 12mm ø12 x 10,5mm 50 pcs.
Page 3
Wooden parts contained in the box. Divider, large Door, right 1 pcs. 2 pcs. Door, left 2 pcs. Side, left Side, right 1 pcs. 1 pcs. Drawerfront, large 2 pcs. 1 pcs. 636 x 157mm Back 4 pcs. Drawerfront, small 1404 x 530mm 4 pcs.
Page 4
A Guide to Wall Mounting & Fixings IMPORTANT: When drilling into walls always check that there are no hidden wires or pipes etc. Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualified tradesperson if you are unsure. HINTS: 1) General Rule Always use a larger screw and wall plug if you are not sure.
Page 5
Key diagram. Function of cam & bolt. Step 1: Step 3: Step 4: Step 2: Fix the bolt to the Push the wooden panel Place the cam into the Tighten: Turn the cam to wooden panel. with the attached bolt onto hole, arrow pointing the right.
Page 6
1. Mounting the cross plates to the sides. Fix the cross plates "Q" to the sides "1" and "2" using screws "H" into the holes indicated. Side, right Front 8 pcs. 4 Pcs. It is important that the cross plates is placed exactly as shown.
Page 7
2. Mounting the hanging rail cups to the sides. Fix the hanging rail cups "L" onto the sides "1" and "2" using screws "G" into the pre-drilled holes. See fig. 2.1 4 pcs. Side, right 2 pcs. Fig. 2.1 Side, left 3.
Page 8
4a. Mounting the cross plates to the large divider. Fix the cross plates "Q" to the left hand side of the large divider "3" using screws "G" into the holes indicated. It is important that the cross plates is placed exactly as shown.
Page 9
5a. Mounting the hanging rail cup to the large divider. Fix the hanging rail Fig. 5a.1 cup "L" to the left hand side of the large divider"3" 2 pcs. using screws "G" into the pre-drilled holes. See fig. 5a.1 1 pcs. Divider, large 5b.
Page 10
7. Mounting the magnets to the top. Fix the magnets "M" to the top "6" using screws "G" into the pre-drilled holes. 8 pcs. Front edge It is important that the 4 pcs. magnetic part points towards the front edge of the top.
Page 11
11A. Assembling the bottoms to the large divider. Push the bolts "E" through the holes Short end indicated on the large Long end divider "3". It is important that the bolts is turned exactly as shown. 2 pcs. Press the bottom "8" onto the left hand side Divider, large of the large divider "3".
Page 12
12. Assembling the right hand side to the bottom. Press the side "2" onto the bottom "8". See page 4 - "Function of cam & bolt". Place the cams "A" into the holes indicated, arrows Side, right pointing towards the side/bolt.
Page 13
14. Assembling the left hand side to the carcass. Press the side "1" onto the bottom "8" and the plinths "7". See page 4 - "Function of cam & bolt". Place the cams "A" into the holes indicated, arrows pointing towards the side/bolt.
Page 14
15. Assembling the top to the carcass. Lower the top "6" onto the divider "3" and the sides "1" and "2". See page 4 - "Function of cam and bolt". Place the cams "A" into the holes indicated, arrows pointing towards the top/bolt.
Page 15
16. Adding the back to the carcass. Place the back "12" into the rabbet of the top "6" and the side "2". Rabbet = Back Ensure there is NO GAP between the side and the back, NOR between the top and the back. Fasten the back with nails "D"...
Page 16
17. Adding the back and the joining strip to the carcass. Place the joining strip "R" onto the back. See Fig. 17.1 Place the back into the rabbet of the top "6". Fig. 17.1 Fasten the back along the top. Use the nail Joining strip guide - see page 14, fig.
Page 17
18. Mounting the drawer sides to the small drawer back. Fix the drawer sides "13" and "14" to the small drawer back "15" 4 pcs. using screws "J". 4 pcs. The grooves of the drawer sides and back should be turned exactly as shown.
Page 18
21. Adding the small drawer front to the drawer frame. Press the drawer front "11" onto the drawer sides "13" and "14". See page 4 "Function of 12 pcs. cam and bolt". Place the cams "B" into Drawer front, small the holes indicated, 4 pcs.
Page 19
23. Mounting the drawer sides to the large drawer back. Fix the drawer sides "13" and "14" to the large drawer back "16" 2 pcs. using screws "J". The grooves of the drawer sides and back should be turned 2 pcs. exactly as shown.
Page 20
26. Adding the large drawer front to the drawer frame. Press the drawer front "10" onto the drawer sides "13" and "14". See page 4 "Function of 8 pcs. Drawer front, large cam & bolt". 2 pcs. Place the cams "B" into the holes indicated, arrows pointing towards the drawer front / bolts.
Page 21
28. Adding the drawers & the hanging rail to the carcass. Slide the drawers onto the drawer runners. Lower the hanging rails "P" into the hanging rail cups. Hanging rail 2 pcs. Page 21 of 25 Scandinavia 4 door robe w/ 2+4 drws.
Page 22
29. Mounting the hinges to the doors. Press the hinges "N" into the holes indicated on the Door, left doors "4" and "5". Door, right 2 pcs. Fix the hinges using 2 pcs. screws "G". Fig. 29.1 16 pcs. 8 pcs. 30.
Page 23
31. Mounting the doors to the carcass. When placing the doors, the magnet catches MUST point upwards. Step 1 Fig. 31.2 Place the "adjustment hole" of the cup hinge at Cross plate the level of the "fixing screw". Fixing Fig. 31.1 Push the cup hinge screw towards the cross plate -...
Page 24
32. Adjusting the doors. MAKE SURE THE WARDROBE IS PLACED ON A PLANE SURFACE BEFORE YOU BEGIN TO ADJUST THE HINGES. Step 1 - right or left: Loosen the fixing screw. To adjust the door towards the left To adjust the door towards the Continue adjustment - see step 2 - hand side - turn the adjusting right hand side - turn the adjusting...
Page 25
Dear Customer. Please note that the product you have purchased is a natural living timber. Just like nature itself, wood varies in shape and colour. Knots, vein patterns, resin pockets and colour differences contribute to giving the piece of furniture its beauty and form - a natural part of solid wood.
Page 27
Safety and Care Advice Important - Please read these instructions fully before starting assembly Care and maintenance Only clean using a damp cloth From time to time check that This product should not be and mild detergent, do no use there are no loose screws on discarded with household waste.
Page 36
Assembly instructions 11b. Assembling the bottoms to the large divider. Press the bottom "8" onto the large divider "3". See page 5 "Function of cam and locking pin". Place the cams "A" into the holes indicated, arrows pointing towards the side / locking pin. Tighten: Turn the cams to the right.
Page 37
Assembly instructions 13. Adding the plinths to the side and the large divider. Press the plinth "7" onto the side "2". The dowels at the end of the large divider "3" should fit into the holes on the plinths. See page 5 "Function of cam and locking pin".
Page 46
Step 33 Fixing to wall It is recommended that the wardrobe is fixed to a wall. Fix wall strap to top wardrobe using screw Will help, move wardrobe into position. Warning: wardrobe is heavy. Lift with care. Mark fixing hole on wall and remove wardrobe Drill 7mm hole and insert...
Page 47
A Guide to - Wall Mounting & Fixings Important: When drilling into walls always Important note: check that there are no hidden wires or pipes etc. If plastic wall plugs Make sure that the screws and wall plugs being used are are supplied with your suitable for supporting your unit.
Page 70
A Guide to - Wall Mounting & Fixings Important: When drilling into walls always Important note: check that there are no hidden wires or pipes etc. If plastic wall plugs Make sure that the screws and wall plugs being used are are supplied with suitable for supporting your unit.
Page 71
Dear Customer Dear Customer Please note that the product you have purchased is a natural living timber. Just like nature itself, wood varies in shape and colour. Knots, vein patterns, resin pockets and colour differences contribute to giving the piece of furniture its beauty and form - a natural part of solid wood.
Need help?
Do you have a question about the Scandinavia 4 door robe w/ 2+4 drws. and is the answer not in the manual?
Questions and answers