Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Dancover San Pablo
Summary of Contents for Dancover San Pablo
- Page 1 Manual Gazebo San Pablo 3x5,8m and 4x5,8m 12-07-2023...
- Page 3 Parts list Table Label No. Part description Drawing Column I Column II Beam (Left) Beam(Right) Front and rear beam I Front and rear beam II Middle beam with gear box Middle beam Louver Column bottom plate Column cover plate Connectors for middle beams Hinge ring Hand crank...
- Page 4 Label No. Part description Drawing Countersunk head screw Pan head screw Flat washer Screw+nut Flat washer Self-drilling screw Woodworking screw+ plastic expansion pipe Glass glue Plastic jam Cover plate for middle column Drainage outlet Bottom plate for middle column Corner support Screw cover Please Note: R and K6 is an optional..., if you do need install them, please refer to the last pages first.
- Page 5 ． ． • •I• • 1. Clamp the drainage outlet P into the column slot, then connect the bottom plate F/Q on the column A1/A3, and tighten with K1 screws. •' step 1 ＜ ＜ QTY: 4PCS QTY: 2PCS 亿 ）...
- Page 6 2. Place the connector H on one side of middle beam D1/D2, then tighten it with K1 screws; complete the other side of middle beam D1/D2 accordingly. Complete three beams with connector H accordingly � <J- step 1 诩 卢 QTY: 24PCS QTY:6PCS ·...
- Page 7 3. Put two hinge rings I into the gearbox drive shaft on the beams D1, then tighten them with K4 screws + nuts. D I / 匾 step 2 step 1 ®飞勹 I CQT Y :4PCS M4x 2 0 QT Y :4PCS Page 3...
- Page 8 4. Place the columns and beams as shown in the below drawing Page 4...
- Page 9 5. The two ends of the front and rear beam C1 must be inserted into the corner connectors of columns A1 and A3; then tighten them with K1 screws. step 2 step 1 ． ． • • 诩 M6X16 QTY: 4PCS Page 5...
- Page 10 6. In the same way, the ends of left and right beams B1 must be inserted into the corner connectors of the column A1, then tighten them with K1 screws. 闷 M6X16 QTY: 4PCS Page 6...
- Page 11 7. According to the step 5 and 6, insert other beams with the corner connector of columns, then tighten them with K1 screws. 闷 M6X16 QTY:16PCS Page 7...
- Page 12 8.The 4 column cover plates G and middle column cover plate P must be mounted on top of the corner connectors of the columns and beams, then tighten them § with K2 and K1 screws. step 2 严 QTY:18PCS QTY: 4PCS 淑...
- Page 13 9. Align the corner supporter R with the bottom the bottom edge of the beam B1, edge of the beam, fix it with self-drilling screw K6. Install the remaining corner supports in turn under each of the beams. Please note: The corner supporters should be removed if one side need to be installed screen.
- Page 14 10. Adjust the position of the six columns so that they are perpendicular to the ground. Also check that the distance between each two columns is the same on both the top and in accordance with the width of the bottom of each two columns. the bottom.
- Page 15 11. Remove the product aside from the marks you just made on the ground. Drill holes at 16 mark positions on the ground with a percussion drill. of 10x80mm in the ground at all 24 marks, using a percussion drill. Drilling depth 10x80 Drilling quantity 24pcs...
- Page 16 12. Place the plastic expansion pipes into the holes drilled in the ground. Reposition the product on top of the drilled holes in the ground and make sure to perfectly match the holes in the column bottom plates with the holes in the ground; then set the flat washers K5 into woodworking screws L and fix them in the ground one by one.
- Page 17 13. Coat the glass glue M evenly on the drain of columns and joints of beams. QTY: 2PCS Page 13...
- Page 18 14. Place the middle beam D1/D2 onto the front and rear beams C1/C2. Page 14...
- Page 19 15. As shown in below figure, Insert louver E at the end of the brackets of at both side of the on the end of the brackets on both sides of the beams (B1-D and B2-D), beams first, then press down the louver to make it clamp and install in the direction by the arrow at the position 1 and 2 respectively.
- Page 20 16. Set the flat washers K3 into the screws K2 at first, fix them into the holes below beam D1/ D2, then align the screws K2 with flat washers with the holes on the top of the beam C1/C2 and tighten it. Install the other louvers in turn.
- Page 21 17. Adjust the louvers Step 2: As shown below, insert a Step 3: After the screwdriver into place 1 and adjust the adjustment, the hole of Step 1: As shown below, if the holes louver support in direction 2, so that louver support is the hole of the louver support is are not concentric, need adjustment.
- Page 22 18. Insert plastic jams into two sides of each louver. 1. The following image shows how to insert plastic jam into foremost louver. 2. Turn the louver halfway and insert the plastic jam into the holes at its two ends. Continue in the same way for each louver in turn.
- Page 23 19. Put the hand crank J on, turn to open/close the flap; installation completed. Page 19...
- Page 24 Following images are optional screen set matched to pergola, the R and K6 should be removed if you need to install the screen set. Optional 1: Screen/Sidewall Optional 2: Alu. turnover louvered wall Optional 3: Glass door...
-
Page 25: Contact Information
Contact information Austria Belgium Croatia Denmark Estonia Finland France Germany Ireland Italy Latvia Lithuania Nederland Norway Poland Portugal Spain Sweden Switzerland For more information please visit: www.dancovershop.com...
Need help?
Do you have a question about the San Pablo and is the answer not in the manual?
Questions and answers