Advertisement
Quick Links
Advertisement
Related Manuals for Dancover San Pablo PA153020
Summary of Contents for Dancover San Pablo PA153020
- Page 1 Manual Gazebo San Pablo 3x5,8m and 4x5,8m 13-01-2021...
-
Page 2: Manual Instruction
Manual Instruction... - Page 3 Parts list table Label Part Drawing Description Column I Middle column Beam (Left) Beam (Right) Front and rear beam I Front and rear beam II Middle beam with gear box Middle beam 6*3=88 8*3=88 Louver 6*4=120 8*4=120 Column bottom plate Column cover plate Connectors...
- Page 4 Parts list table Label Part Drawing Description Hinge ring Hand crank Hexagon socket countersunk head screw Hexagon socket button head screws Flat washer Cross recessed pan head screw + Flat washer Wooden screw+ Plastic expansion pipe Glass glue 6x3=176 8x3=176 Plastic plug 6x4=240 8x4=240...
- Page 5 Optional: P STEP 1: Clamp the drainage connector P into the column slot. STEP 2: Fix the bottom plate F to the column A1/A3 with screws K1. Column A1 Middle Column A3...
- Page 6 Middle Column A3 Column A1 Bottom Plate Q Bottom Plate F Fix the column bottom plate F and Q to the column A1/A3 with the screws K1.
- Page 7 Middle beam D1 STEP 2: Insert the hinge ring I into the gearbox shaft STEP 1: and fix it with screw Fix the connector to and nut K4. the middle beam D1, D2 with screws K1. Middle beam D2 STEP 3： Place the column as shown in the figure below.
- Page 8 Insert the beam B1 into the column A1 and fix it with screws K1. Beam B1 Column A1 Column A1...
- Page 9 STEP 1: Insert the beam C1 into the column A1, A3 and fix it with the screw K1. Beam C1 Column A1 Middle Column A3 STEP 2: Fix the columns to the beams with screws K1 as the figure below. Beam C1 Beam C2 Beam B1...
- Page 10 STEP 1: Fix the cover plate G to the columns and beams with screws K2 as the figure below. Screws STEP 2: Fix the cover plate O to the columns and beams with screws K2 and K1 as the figure below.
- Page 11 STEP 1: Adjust the position of 6 columns to keep them perpendicular to the ground. Meanwhile, the width of the top of each two columns should be measured in accordance with the width of the bottom of each two columns. Then use a market pen to mark 24 holes on the ground, which should be corresponding to the holes in the bottom plate.
- Page 12 STEP 1: Remove the product from the mark and drill holes of ∅10X80 at 24 mark positions on the ground with a percussion drill. Drill depth: ∅10x80 Drill qty: 24pcs STEP 2: Place the plastic expansion pipe in the bottom hole of the column; then move the product back to the hole drilled, align holes of the column bottom plates with the hole drilled on the ground;...
- Page 13 STEP 1: Coat the glass glue M evenly around 6 drain of column and joints of beams. STEP 2: Place the middle beams D1/D2 on the front and rear beams C1/C2. Beam C2 Middle beam D1 Beam C1 Middle beam D1 Beam C1 Beam C2 Middle beam D2...
- Page 14 Louver E STEP 1: As shown in the figure below, clip the louver E into the tail of the bracket of the beams at both ends first, then press down the louver to make it clamp and install in the direction indicated by the arrow at the position 1 and 2 respectively.
- Page 15 STEP 1: Align and fix the hole under D1/D2 with screws K2 and washer K3; then Align and fix the hole on the C1/C2; Install the remain louvers in turn. Beam C1 Beam C2 Beam D1 Beam D1 Beam D2 Beam C2 Beam C1...
- Page 16 Insert a straight If the holes are not screwdriver into position 1 aligned as figure and move the louver below, adjustments supporter according to will be required direction 2 to make holes Holes are concentric concentric after adjusting...
- Page 17 The plastic jam installed at STEP 1: the front fixed louver Insert plastic N jam into holes at two ends of the louvers.
- Page 18 STEP 1: Put the hand crank J on, turn to open/close the louvers; installation completed.
- Page 19 Head office: Dancover A/S For more information Lyngevej 16A, Nørre Herlev please visit: 3400 Hillerød www.dancovershop.com Denmark...
Need help?
Do you have a question about the San Pablo PA153020 and is the answer not in the manual?
Questions and answers