Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Dancover PA152005
Summary of Contents for Dancover PA152005
- Page 1 Manual Gazebo 2,95x2,95x2,7m 28-11-2019...
- Page 2 Assembly Instructions PRODUCT SIZE(LxWxH):295x295x270cm PLEASE READ CAREFULLY BEFORE ASSEMBLY...
- Page 3 CONTENTS...
- Page 4 Assembly and Maintenance Advice 1. For safety purposes, we strongly recommend that this product is assembled by at least two people. 2. Some components have sharp metal edges. Please be careful when handling metal components. Please wear gloves, shoes and safety goggles during assembly. 3.
- Page 5 Functions and Features: 1. Compared with traditional greenhouses this new product features many significant improvements. The hollow box profile aluminium framing is much stronger than other greenhouses and it can withstand much greater pressure. 2. Base anchor brackets are included as standard with expanding bolts to ensure a secure fixing into concrete or paving.
- Page 6 5. Manual window handles are included as standard with the roof vents. If required, automatic roof vent openers are available as an inexpensive optional extra. Manual Opener Automatic Opener 6. Remove approximately 2 inches of film from all sheet edges before installing and remove all film immediately after the construction is completed.
- Page 7 PA152000 PART PART L01A L04A L04B WindowX2 DOOR L05A PART L07A PART L19A L08A L19B L09A L23A L18A L03B L18B L03C L18C L05E L18D L15A L05F PART L02E L03D L05B M5X12 L05C M5X12 M4.2X16 L03A Ø4X14D M4.2X16 M8X60...
- Page 8 PA152000 PA RT PA RT 126M Rubber for walls & roof (Provided for glass only) PC/Glass PA RT Rubber for walls only Y 10 (Provided for glass only) Y 11...
- Page 9 PART Window L19A L19B M4.2X16 L19A L19A Fix W06 in the middle of L19B, L19B 322.2mm from the ends. Screws position L19B Screws position 20MM Insert Connector B & W07 into each end of frame profiles L19A & L19B & L20, and then fix them with screws Z01.
- Page 10 PART PART 2.65M L15A L15A M4.2X16 Ø4X14D If glass is chosen, please seal it with rubber(J11) provided. Rubber is not provided if you choose polycarbonate sheet as glazing panel.
- Page 11 PART Left Door L18A L18A L18B L18C L18D L18D M5X12 M4.2X16 L18B 20MM 30MM Insert Connector A into each end of frame profiles L16 & L18A & L18B & L18D, and then fix them with screws Z01. Before fixing with screws, please mark them with a pencil at distance about 20/30mm from each end, and make sure there is no gaps between each profile.
- Page 12 Right Door L18B L18C L18A 20MM 30MM Insert Connector A into each end of frame profiles L16 & L18A & L18B & L18C, and then fix them with screws Z01. Before fixing with screws, please mark them with a pencil at distance about 20/30mm from each end, and make sure there is no gaps between each profile.
- Page 13 PART 12.2M If glass is chosen, please seal it with rubber(J11) provided. Noted: Rubber is not provided if you choose polycarbonate sheet as glazing panel.
- Page 14 Expansion screw/Concrete ground It is essential the dimensions a + b are the same to ensure the base is square. Steel pegs in soil Support at the corners only is inadequate.
- Page 15 PART M8X60 2899MM Expansion bolts assembly Door...
- Page 16 PART L08A M5X12 L08A L08A L08A L08A L08A Insert J02 into each L08A, and then fix them with W26 and S01. Make sure the angle is Right Angle before tighting up S01.
- Page 17 PART L01A L07A L01A L01A M5X12 L01A L01A L01A Install L01A, connect them with W26, and fix them with S01. Insert J01 into L01A, and then connect each L07A; fix them with W26 & S01. Make sure the angle is Right Angle before tighting them up. L07A L07A L07A...
- Page 18 PART Back Wall Assembly L03A L03A L03A L03A M5X12 L07A L07A L01A L01A L08A L08A L08A L08A Insert Panel Y5 into the channel of L01A, and then fix a L03A onto L08A & L07A using S01. Make sure the other side of Y5 is completely in the channel of L03A.
- Page 19 PART L03A M5X12 L03A L03A L07A L03A Side Walls Assembly Do the same as the back wall assembly, Y6 is the last panel to slide in. L08A L03A The last panel...
- Page 20 PART Front Wall Assembly L04A L04B L05B M5X12 L04B L04A L07A Fix L04A/L04B and Y5 same as the L03A back wall assembly using S01. And then fix 1 X L05B to L01A & L04A and 1 X L05B to L01A & L04B using S01. L03A L08A L05B...
- Page 21 PART L05A M5X12 M4.2X16 L01A L01A L05A L05A Install L05A (3PCS) Fix two ends of L05A onto L01A using S01, Fix L05A to L03A with the self-tapping screws (Z01) using a powered screwdriver. Eusure that L05A is fixed at a right angle (90 degrees) to the glazing bars.
- Page 22 PART L02E M4.2X16 Aligned overlap L02E L05A Install L02E (2PCS) Insert the other end of Y6 into the channel of L02E, and then fix it onto L05A, using Z01. Make sure L02E and L05A must be aligned.
- Page 23 PART WINDOW M5X12 M4.2X16 1. Fix W03 onto the window profile L11 using S01; 2. Make a mark on L03A at distance 643MM from L02E (as shown on the left). Do the same on the other end. 3. Install the window on L03A, fixing with Z01. 4.
- Page 24 PART 59.5M If glass is chosen, please seal it with rubber(J11) provided.
- Page 25 PART L23A Roof Assembly L23A L23A L23A M5X12 L23A L23A Fix 4 X L23A onto W23 as shown above, using S01. L23A L07A L23A Connect the roof profiles to the eave profiles L07, using connector W21. Fix them with S01. Note: a partner is needed to hold the profiles when you do this assembly.
- Page 26 PART L03D M5X12 L03D L03D L03D Fix L03D (4 PCS) on the roof as shown, using S01. Twist M01 into the bolt on W24, and then insert the bolt of W24 through W23. Adjust the position of the above M01 to allow enough space for another M01 below to tight it up.
- Page 27 PART PART 46.2M L03B L03C L03C L03B L09A M5X12 L03B&L03C L03B&L03C Install L03B & L03C on L07A & L23A as shown Y1&Y2 Insert Y1/Y2 into the right position before fixing L03B /L03C. If glass is chosen, please seal it with rubber(J11) provided.
- Page 28 Install Y3 & Y4 If glass is chosen, please seal it with rubber(J11) provided.
- Page 29 PART Gutter Assembly 45.2M When the panels are completely inserted, fix gutter profile L09A. Tap it gently into position with a rubber mallet. L07A L09A Do the same on the other sides...
- Page 30 PART L05C L05E L05F L05E L05F M4.2X16 M5X12 L05C L05E L03D L03B&L03C L03B&L03C L05C L05C Fix L05C onto L03B & L03C using S01, and use Z01 to fix it onto L03D. Install the eave bracing L05E using Z01 as shown.
- Page 31 PART Door Assembly M4.2X16 M5X12 M5X12 Left Door Right Door Install L24 onto L07A, using Z01. Left Door Right Door Fix L25(4 PCS) one side on the door profile and the other side on L04A/L04B using S02. Then secure with Z03.
- Page 32 PART M4.2X16 If you wish to eliminate leaks Drill a hole in L01A, use glue when fixing the downpipe approximately 3mm diameter and 700mm bends (not provided). up from the bottom. Fix the J08 downpipe bracket with Z01 screws and then clip the J06 downpipe into the J08 bracket.
- Page 33 Contact information Head office: Dancover A/S For more information Nordre Strandvej 119 G please visit: 3150 Hellebæk www.dancovershop.com Denmark National contact Denmark: 70 26 76 20 Spain: 911 436 828 denmark@dancover.com espana@dancover.com UK: 020 8099 7570 Italy: 02 479 21 198 uk@dancover.com...
Need help?
Do you have a question about the PA152005 and is the answer not in the manual?
Questions and answers