Seneca MyALARM2-4G Installation Manual

Gsm remote alarm and data logger unit, security audio version

Advertisement

Quick Links

PRELIMINARY WARNINGS

The word WARNING preceded by the symbol
risk. The word ATTENTION preceded by the symbol
instrument or the connected equipment.
The warranty shall become null and void in the event of improper use or tampering with the module or devices
supplied by the manufacturer as necessary for its correct operation, and if the instructions contained in this
manual are not followed.
WARNING: The full content of this manual must be read before any operation. The module must only be used by
qualified electricians. Specific documentation is available using the QR-CODE shown on page 1.
The module must be repaired and damaged parts replaced by the Manufacturer.
The product is sensitive to electrostatic discharges. Take appropriate measures during any operation.
Electrical and electronic waste disposal (applicable in the European Union and other countries with recycling).
The symbol on the product or its packaging shows the product must be surrendered to a collection centre authorized
to recycle electrical and electronic waste.
DOCUMENTATION
SENECA s.r.l.; Via Austria, 26 – 35127 – PADOVA – ITALY; Tel. +39.049.8705359 - Fax +39.049.8706287
CONTACT INFORMATION
Technical support
This document is the property of SENECA srl. Copies and reproduction are prohibited unless authorised.
The content of this document corresponds to the described products and technologies.
Stated data may be modified or supplemented for technical and/or sales purposes.
MI00613-0-EN
INSTALLATION MANUAL
MyALARM2-4G
My2SL
support@seneca.it
INSTALLATION MANUAL
indicates conditions or actions that put the user's safety at
indicates conditions or actions that might damage the
Product information
My2GL
DOCUMENTATION
sales@seneca.it
1/8

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MyALARM2-4G and is the answer not in the manual?

Questions and answers

Summary of Contents for Seneca MyALARM2-4G

  • Page 1 The symbol on the product or its packaging shows the product must be surrendered to a collection centre authorized to recycle electrical and electronic waste. My2SL My2GL DOCUMENTATION DOCUMENTATION SENECA s.r.l.; Via Austria, 26 – 35127 – PADOVA – ITALY; Tel. +39.049.8705359 - Fax +39.049.8706287 CONTACT INFORMATION Technical support support@seneca.it Product information sales@seneca.it This document is the property of SENECA srl.
  • Page 2 MODULE LAYOUT CASE DIMENSIONS SYMBOLS ON THE ENCLOSURE ON / OFF power button GPS antenna Menu access button Slot for mini SIM Slot for micro SD card Micro USB connector 80 mm 8 mm 32 mm Weight 150 g Case Polycarbonate / ABS material SIGNALS VIA LED ON FRONT PANEL STATUS...
  • Page 3 BANDS GSM/GPRS/EDGE 900/1800 MHz Seneca recommends use between 0 and 45°C for the battery correct operation. Temperature: with the power supply present: -20 ÷ +55°C; with use of the battery (when discharged): -20 ÷ +45°C. Charging is possible in the range: 0 ÷ +45°C.
  • Page 4 INITIAL POWERING ON OF THE DEVICE Device is supplied in “shipping mode”. This mode prevents any unnecessary discharge of the battery during transport as well as any accidental switch-ons. To exit this mode, simply power the device via the cable supplied. N.B.: During “shipping mode”...
  • Page 5 ASSEMBLY REGULATIONS The device has been designed for vertical installation or on a DIN IEC EN 60715 omega rail. Avoid mounting the device inside metal cabinets or on top of heat-generating equipment. INSTALLATION ON DIN IEC EN 60715 RAIL AND WALL FIXING As shown in the figure on the side: 1.
  • Page 6 ELECTRICAL CONNECTIONS INSERTION AND EXTRACTION FROM TERMINALS WITH A PUSH-WIRE CONNECTION Insertion of a rigid cable Insertion of a thin cable Extraction of a rigid cable A: press with a A: press with a screwdriver screwdriver Press down Recommended flaying: B: insert B: extract 8-9 mm...
  • Page 7 DISPLAY FUNCTIONS AND USE The main display page provides the following information: A - Network signal level B - outlet 1 status C - outlet 2 status D - digital input 1 status E - digital input 2 status F - digital input 3 status G - digital input 4 status H - battery level To change the page on the display, use the SCR key as shown in the "INITIAL POWERING"...
  • Page 8 PRODUCT ID CODE A label will be applied to the product packaging that allows you to recognize the model purchased. Find below the meaning of the codes applied to the packaged instrument: SL GL R 0 W 0 C M B G EQUIPMENT MODEL: RELAY:...

Table of Contents