Table of Contents
Advertisement
41 Commissioning
41
Commissioning
PoolManager
®
has a menu for the first start'up
parameters relevant to successful installation.
This menu for first start'up can be called up at a
! ;
The following steps are executed:
Action
Entry
Step 1: Menu language
Configuration of menu language
Step 2: Set default values
Here, the desired default set
Here, select the defa
can be selected and
cases of doubt, plea
activated.
values for their validi
installation.
For safety reasons, a
has to be confirmed
Step 3: System parameters
Configuration of pool and
Pool volume of the c
system parameters
pool.
Hose configuration o
This display is used
made at the factory a
configuration.
Variation A: PoolManager
®
Oxygen:
Step 4: Calibration
Calibration (comparison) of
1'point calibration pH
measured pH value
described in the sect
Step 5: Control parameters pH
Configuration of the most
When refilling the po
important parameters for
expand the top and b
pH control
and to adjust the p'ra
can fluctuate somew
phase.
CAUTION: If the par
make absolutely sure
back as soon as the
stabilised.
You can also use th
Step 6: Manual dos. O2 (Bayrosoft
®
)
Start manual dosing
The dosing volume (
water volume) is calc
pool volume and can
In order to increase t
the first dosage, ther
certainty of disinfecti
select 2x or 3x the d
Step 7: Dosage parameters O2
Configuration of the most
Dosage volume is c
important parameters for
pool volume and is d
automatic Bayrosoft
dosing.
(0.5l Bayrosoft
®
be changed manuall
Select the dosage da
before the largest wa
(e.g. high amount of
Temperature compe
more Bayrosoft
temperatures (highe
should be set at leas
up. This menu covers all
at any time as follows:
-
$
efault set that best fits. In
lease check all default
lidity for the respective
s, activation of the defaults
ed at this point.
e connected swimming
n of the pump hoses used.
ed to check the settings
ry according to device
pH. Please proceed as
ection -
pool, it may be sensible to
d bottom pH value alarms
range, as the pH value
ewhat during the starting
parameters are changed,
sure that the values are set
the pool water has
the configuration assistant.
e (for 0.5l Bayrosoft
®
/10m
3
calculated upon entering the
can be started here.
se the dosage volume for
hereby increasing the
ection, it's also possible to
e dosage volume.
calculated by entering the
is displayed here to check
/10m
0m
water volume). It can
®
3
ally.
day such that it is directly
t water usage expected
t of swimming).
pensation ensures that
®
is d
is dosed for higher water
her product consumption). It
east to normal.
Variation B: PoolManager
®
Chlorin
rine/Bromine
Step 4: Calibration
Calibration (comparison) of
1'poi
point calibration pH. Please proceed as
measured value for pH and
descr
scribed in the section -
redox
1'poi
point calibration mV (optional). Please
proce
oceed as described in the section
-
Step 5: Control parameters pH
Configuration of the most
When
hen refilling the pool, it may be sensible to
important parameters for
expan
pand the top and bottom pH value alarms
pH control
and t
d to adjust the p'range, as the pH value
can fl
n fluctuate somewhat during the starting
phase
ase.
CAUT
UTION: If the parameters are changed,
make
ake absolutely sure that the values are set
back
ck as soon as the pool water has
stabil
abilised.
You c
u can also use the configuration assistant.
Step 6: pH Value configuration
Possibility for automatically /
Displ
splay shows the configured pH setpoint and
manually setting the pH value
the cu
e current pH value in the pool water.
in the pool water
NOTE
TE The pool water's pH value first has to
be se
set to pH 7.2 in order to facilitate
config
nfiguration of the redox value without issue.
Set p
t pH operation mode to auto if
PoolM
olManager
fully a
lly automated. This process will take some
time,
e, depending on pool size and water
qualit
ality.
Set o
t operating mode to manual if you would
like to
e to configure the pH value via manual
additi
dition of pH'elevator and 'reducer.
Step 7: Manual dosing mV (Cl / Br)
Configure the desired
The m
e matching setpoint will depend on the
chlorine or bromine level and
pool.
ol. It has to be calculated for the water in
calculate the associated
the re
e respective pool. Proceed as follows:
redox (mV) value
Set th
t the pH value to pH 7.2
(see
ee previous step)
Set th
t the desired chlorine level in the pool via
manu
anual dosing (or via manual addition of
chlori
lorine) The volume of sodium hypochlorite
dosed
sed is determined by PoolManager
the p
e pool volume entered. This volume can be
overw
erwritten manually.
Chec
eck the desired chlorine level via manual
meas
easurement (DPD). The redox value in
[mV],
V], which PoolManager
desire
sired chlorine volume, is also the value that
has to
s to be entered as the setpoint in the next
step.
ep.
Step 8: Control parameters redox (mV
(mV)
Configuration of the most
Set th
t the mV value as the setpoint you read in
important parameters for
the p
e previous step for the desired chlorine
redox control
level.
vel. Adjust the bottom and top alarm
accor
cordingly. Check the proportional range.
You c
u can also use the configuration assistant.
In the individual menu pages, i
, it is possible to scroll forward and
backward at any time.
For further information, please re
refer to the corresponding chapters in
this user's manual or to the help fu
p function on the device.
' 9 * .,
®
should make the configuration
®
via
®
shows for the
75
Advertisement
Table of Contents
