Related Manuals for HPE Aruba Networking 2930M
Summary of Contents for HPE Aruba Networking 2930M
- Page 1 HPE Aruba Networking 2930M Switches and Accessories Start Here: Installation, Safety, and Regulatory Information Published: January 2024 Edition: 2...
- Page 2 Hewlett Packard Enterprise Company. To obtain such source code, please check if the code is available in the HPE Software Center at https://myenterpriselicense.hpe.com/cwp-ui/software but, if not, send a written request for specific software version and product for which you want the open source code.
- Page 3 Notices The information contained herein is subject to change without notice. The only warranties for Hewlett Packard Enterprise products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
-
Page 4: Applicable Products
See the rest of this guide for important presetup information. There are no user-serviceable parts in the HPE Aruba Networking 2930M switches or the AC adapter used with some 2930M switch models. For switch or accessory service needs, contact an authorized HPE Aruba Networking representative. -
Page 5: Installation Precautions And Guidelines
For the air flow direction, see the Installation and Getting Started Guide for your product by visiting the Hewlett Packard Enterprise Support Center at http://www.hpe.com/support/manuals. If a power supply must be removed, and then reinstalled, wait at least 5 seconds before re- installation. -
Page 6: Prepare For Installation
Aruba X372 54VDC 1050W 110-240VAC Power Supply (JL087A) 3. Power on and verify that self-test completes normally. An HPE Aruba Networking 2930M switch does not contain a power on/off switch. It is turned on by connecting the AC power cord to the switch and to an AC power source. -
Page 7: Power Cords
Different countries/regions may require different power cords. For a list of the power cords that apply to your HPE Aruba Networking 2930M switch, see the section that lists power cords in the latest edition of the HPE Aruba Networking 2930M Switch Series Installation and Getting Started Guide. - Page 8 Only HPE Aruba Networking-approved power cords may be used with HPE Aruba Networking devices. To access the power cord information for your switch, see the latest edition of the HPE Aruba Networking 2930M Switch Series Installation and Getting Started Guide. Lost or damaged power cords must be replaced only with HPE Aruba Networking-approved power cords.
- Page 9 Information For important safety, environmental, and regulatory information, see Safety and Compliance Information for Server, Storage, Power, Networking, and Rack Products, available at http://www.hpe.com/support/Safety-Compliance-EnterpriseProducts. HPE Aruba Networking 2930M Switch Safety and Regulatory Information HPE Aruba Networking 2930M Switches Environmental All switches except the JL324A: Operating Temperature: 0°C to 55°C (32°F to 131°F) up to 5000 ft...
- Page 10 HPE Aruba Networking 2930M Switches North American UL60950-1, CSA 22.2 No 60950-1 Lasers EN60825-1:2007 / IEC 60825-1: 2007 Class1 Class 1 Laser Products / Laser Klasse 1 EN 55032:2012, Class A EN 55024:2010 EN 61000-3-2:2014, Class A EN 61000-3-3:2013 FCC CFR 47 Part 15:2010, Class A...
- Page 11 Table 1: Power Cord for HPE Aruba Networking 2930M PoE+ Switches One of the following: Argentina 8121- 1481 Israel 8121-1478 Australia/New Zealand 8121- 1476 Japan high line 8121-1738 Brazil 8121- 1265 Japan low line 8121-1482 (JL086A power supply only) Chile...
- Page 12 The only indicator of battery failure is the failure of the switch internal clock to keep the correct time across a reboot or power cycle. If a battery failure occurs, contact your authorized HPE Aruba Networking representative for assistance. Batteries are not customer-serviceable and battery failures should be referred only to service personnel authorized by HPE Aruba Networking.
- Page 13 CE marking accordingly. For Conducted and Radiated Immunity in accordance with EN55024, the HPE Aruba Networking 2930M switch products are limited to Performance Criteria A with shielded cable for HPE Smart Rate ports.
-
Page 14: Documentation Feedback
2930M Switch This section previews the steps for installing the switches. To find detailed switch installation steps, information on configuration tools, and other instructions and information, see the HPE Aruba Networking 2930M Switche Series Installation and Getting Started Guide. 1. Prepare the installation site.
Need help?
Do you have a question about the Aruba Networking 2930M and is the answer not in the manual?
Questions and answers