Table of Contents
Advertisement
Quick Links
INSTRUCTION
MANUAL
<Specifications>
Maximum Operating Pressure
Air Consumption (No Load)
Rated Speed (No load)
Stroke Length
Shank Dia.
Mass (Weight)
Sound Pressure Level
Sound Power Level
Vibration Level [Uncertainty K]
Thread Size of Air Inlet
*1 Based on the ISO15744 measurement standard.
*2 Based on the 3 axes combined value measurement standard of the
ISO28927-9 of the hand-held tool frequency correction vibration acceleration
effective value.
z Please read this manual carefully before you attempt to use your tool so that you may use it
z
properly and safely.
z Please keep the manual handy - so you can use it whenever necessary.
z
• Due to continuous product development/improvement the specifications and configurations in this
document are subject to change without prior notice.
Manufactured by:
NITTO KOHKI CO., LTD.
Professional Tool
Model: ASH-900
Model
MPa
3
m
/min
min
mm
mm
kg
dB(A)
dB(A)
m/s
9-4, Nakaikegami 2-chome, Ohta-ku, Tokyo, 146-8555, Japan
Tel : +81-3-3755-1111 Fax : +81-3-3753-8791
PNEUMATIC RECIPROCATING FILE
ASH-900
0.6
0.13
-1
6300
9
5
0.5
62.5
73.5
2
4.8 [3.0]
Rc 1/4
TQ12691-5 08/2019
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Nitto Kohki Super Hand ASH-900
Summary of Contents for Nitto Kohki Super Hand ASH-900
- Page 1 • Due to continuous product development/improvement the specifications and configurations in this document are subject to change without prior notice. Manufactured by: 9-4, Nakaikegami 2-chome, Ohta-ku, Tokyo, 146-8555, Japan NITTO KOHKI CO., LTD. Tel : +81-3-3755-1111 Fax : +81-3-3753-8791 TQ12691-5 08/2019...
-
Page 2: Table Of Contents
Instructions Thank you very much for your purchase of this NITTO KOHKI product. Before using your tool, please read this manual carefully so that you may use it properly to get the most out of it. Please keep the manual handy - so you can use it whenever necessary. -
Page 3: (Make Sure To Follow The Instructions Given)
California Proposition 65 WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known [to the State of California] to cause cancer birth defects or other reproductive harm. Some examples of these chemicals are: z Lead from lead-based paints, z Crystalline silica from bricks and cement and other masonry products, and z Arsenic and chromium from chemically-treated lumber. - Page 4 Precautions on Use Work area safety WARNING z Do not use the tool at home. This is a professional tool (industrial or work tool for business). Do not bring the tool home and use it there. z Keep the work area clean. Working in a messy work area or work table could cause an accident.
- Page 5 Handling tools WARNING z Storing the tool When the tool is not used, store the tool in a dry location. Also, store the tool out of the reach of children. For some tools, the storage temperature and humidity are specified. Store the tool in an appropriate location. z Be cautious about how the tool is carried.
- Page 6 This tool shall be inspected periodically to verify the ratings and markings. When a label/nameplate is damaged, worn or missing, contact the sales agent through which you have purchased your tool or NITTO KOHKI Co. Ltd. directly for a replacement.
- Page 7 Projectile Hazards WARNING z Be aware that failure of the workpiece or accessories, or even of the inserted tool itself can generate high- velocity projectiles. z Always wear impact-resistant eye protection while operating this tool. The grade of protection required should be assessed for each operation.
- Page 8 Precautions on Use Accessory Hazards WARNING z Disconnect the tool from the energy supply before fitting or changing the inserted tool or accessory. z Avoid direct contact with the inserted tool during and after use, as it can be hot or sharp. z Use only accessories and consumables that are the sizes and types recommended by the manufacturer of this tool;...
- Page 9 Noise Hazards WARNING z Exposure to high noise levels can cause permanent, disabling hearing loss and other problems, such as tinnitus (ringing, buzzing, whistling or humming in the ears). Therefore, risk assessment and implementation of appropriate controls for these hazards are essential. z Appropriate controls to reduce the risk can include actions such as damping materials to prevent workpieces from “ringing”.
- Page 10 Precautions on Use Product Specific Safety Rules WARNING z Inspect an attachment for chips or cracks prior to mounting. Do not use an attachment that is chipped or cracked or otherwise damaged. z Make Certain the diameter of the attachment mandrel suits the chuck. Fasten the attachment securely.
-
Page 11: Application
If an abnormality is found, request service from the retailer where you purchased the tool or the nearest NITTO service member store. Package Contents Check Package Contents Check SUPER HAND ASH-900 1set Hex. Socket Screw Key 2.5 Rat Tail File SF-10 Bushing R1/4x NPT1/4 Triangular Taper File SF-11... -
Page 12: Air Supply
3 Air Supply CAUTION z Remove drainage before stating work. When drainage enters the tool, the vicinity of the exhaust port freezes, which could cause a loss of power. ① ① Compressor ② Air Filter ② ③ Air Regulator ③ ④... -
Page 13: Mounting And Removing The File
4 Mounting and Removing the File WARNING z Be sure to turn off the air supply and disconnect the air hose. Mounting / Removing the file (Fig. 1) Mounting Insert the file shank into the Holder and tighten the Hex. Socket Set Screw with the Hex. Socket Screw Key until the file is securely fixed. -
Page 14: (Optional Parts) (Fig. 3)
5 How to Operate the Tool WARNING z Always wear eye protection during operations. Start the operation and press the tool slightly to the workpiece. z Even if the tool is strongly pressed, the filing efficiency cannot be improved. Start and Stop (Fig. 2) To start: Turn the Valve Ring clockwise and align "... -
Page 15: Thread Size Of Hose Fitting
How to operate the tool 6 Thread Size of Hose Fitting The product comes with a metal fitting with Rc(metric) thread. Connect the Bushing R thread x NPT thread included as standard accessories, if you would like to have American NPT thread instead. 7 Storage CAUTION z When tool is not used, store it out of reach of children.
Need help?
Do you have a question about the Super Hand ASH-900 and is the answer not in the manual?
Questions and answers