Table of Contents
Advertisement
Quick Links
PNEUMATIC CHAMFERING TOOL
Please read this manual carefully before you attempt to use
your tool so that you may use it properly and safely.
MINI BEVELER
PROFESSIONAL TOOL
AMB-0307
Maximum Operating Pressure
Air Consumption (No Load)
Rated Speed (No load)
Chamfering Capacity
Chamfer Angle
Mass (Weight)
Sound Pressure Level
Sound Power Level
Vibration Level
Thread Size of Air Inlet
Due to continuous product development/improvement the specifications and configurations in
this document are subject to change without prior notice.
Keep the manual handy – so you can use it whenever necessary.
Model AMB-0307, AMBL-0307
Specifications
Model
Stainless Steel
Mild Steel
AMBL-0307
AMB-0307
AMBL-0307
0.6 MPa
3
0.9 m
/min
0.9 m
-1
14,000 min
14,000 min-1
0〜3C,2R,3R,4R
0〜7C,2R,3R,4R
15〜45°
2.9 kg
87 dB (A)
87 dB (A)
98 dB (A)
98 dB (A)
2
1.0 m/s
1.0 m/s
Rc3/8
Manufactured by :
NITTO KOHKI Co., Ltd.
2-9-4, Nakaikegami, Ohta-ku,
Tokyo, 146-8555, Japan
Tel : (81)-3-3755-1111
Fax : (81)-3-3753-8791
E-mail : overseas@nitto-kohki.co.jp
URL : www.nitto-kohki.co.jp
Original Instructions
3
/min
2.9 kg
2
Rc3/8
Advertisement
Table of Contents
Related Manuals for Nitto Kohki AMB-0307
Summary of Contents for Nitto Kohki AMB-0307
- Page 1 PNEUMATIC CHAMFERING TOOL Please read this manual carefully before you attempt to use your tool so that you may use it properly and safely. MINI BEVELER Model AMB-0307, AMBL-0307 PROFESSIONAL TOOL AMB-0307 AMBL-0307 Specifications Model AMB-0307 AMBL-0307 Maximum Operating Pressure 0.6 MPa...
-
Page 2: Table Of Contents
11. ORDERING SERVICE PARTS ………………………… 9 á votre foumisseur de manuel 12. OPTIONAL PARTS ……………………………………… 9 instruction en langue locale. 13. EXPLODED DIAGRAM : AMB-0307, AMBL-0307 … 10 Spanish : Por favor, cantacte con su ・ distribuidor para el manual de instrucciones en español. -
Page 3: Important Safety Instructions
IMPORTANT SAFETY BEFORE OPERATION INSTRUCTIONS Inspect tool before use. ● Before using, check that screws are securely When using the tool, please observe the safety tightened, that any protective cover or guard is precautions below to prevent possible accident or securely in place, other parts are free from damage injury. -
Page 4: General: Pneumatic Tools
Do not carry the tool by the connecting hose. becomes missing, contact the sales agent through Do not pull the connecting hose to disconnect. which you have purchased your tool or Nitto Kohki Co. Ltd, directly for a replacement. DISPOSAL When a tool is taken permanently out of service, it ● ... -
Page 5: Instructions For This Tool
4-2. Air Line (Fig.1) Use a 9.5 mm (3/8”) I. D. connecting hose between AMB-0307 the compressor and the tool. Package Contents Qty Check Drained water, etc., if flown into the tool, could MINI BEVELER cause tool failure. -
Page 6: Preparation
6. HOW TO OPERATE THE TOOL test cut. Then adjust the tool for accurate chamfering. 6-1. Start and Stop AMB-0307 In the case of Mild Steel. To start, pushing the Valve Ring forward and turn it You can select chamfering levels from 0 to 7C freely. - Page 7 Do not make any Scale ② clearance Guide Pin ③ Socket Head Cap Screw ① Head ④ Guide Line Scale Fig. 6 Plate Guide ⑤ Fig. 8 6-3. Adjustment of Radius Chamfering in Amount (1) Fix a radius chamfering Indexable Inserts. α (2) Loosen the Hex. Socket Head Cap Screw ① of the Head ④...
- Page 8 6-6. Feeding Speed Radius cutting Indexable Insert is an optional ● Be sure you should avoid quick feeding or heavy accessory. shock. Please refer to Fig. 12. (1) Select the radius chamfering. Stainless Steel 3cm/sec (2) Make sure that the Valve is set at "OFF" position Mild Steel 2cm/sec and connect the air hose to the tool.
-
Page 9: How To Replace Indexable Insert
6-10. How To Chamfer Outer Diameter 7. HOW TO REPLACE INDEXABLE INSERT WARNING WARNING Be sure to remove the air hose beforehand Always turn off the air supply and disconnect ● whenever the accessories are attached or the air supply hose. removed. -
Page 10: Condition For Use
8. CONDITION FOR USE Burn-out chips suggest that either the feed speed is too slow or the Indexable Insert has worn-out. Change the cutting conditions or check the conditions of the Indexable Insert. 9. THREAD SIZE OF HOSE FITTING The product comes with a metal fitting with Rc (metric) thread. -
Page 14: Declaration Of Conformity
Tel: (65)-6227-5360 Fax:(65)-6227-0192 http://www.nitto-kohki.co.jp/e/nksb/ NITTO KOHKI EUROPE Co., Ltd. Unit 21, Empire Centre, Imperial Way, NITTO KOHKI Co., Ltd. Shanghai Representative Office Watford Hertfordshire, WD24 4TS, United Kingdom #1117 Ruijing Building, Maoming South Road, Tel: (44)-01923-239668 Fax:(44)-01923-248815 Shanghai 200020 China http://www.nitto.co.uk/...
Need help?
Do you have a question about the AMB-0307 and is the answer not in the manual?
Questions and answers