ABS Piranha S10/4W-50 Installation, Operating And Maintenance Instruction

ABS Piranha S10/4W-50 Installation, Operating And Maintenance Instruction

Submersible grinder pump

Advertisement

ABS Piranha submersible grinder pump S10 - PE125
GB
Installation, Operating and Maintenance Instructions
www.cardo.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Piranha S10/4W-50 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for ABS Piranha S10/4W-50

  • Page 1 ABS Piranha submersible grinder pump S10 - PE125 Installation, Operating and Maintenance Instructions www.cardo.com...
  • Page 2: Table Of Contents

    Bearings and Mechanical Seals ..........................14 Maintenance of Lifting Stations in accordance with EN 12056.................. 14 Cleaning ..................................14 Venting of the volute ..............................14 Troubleshooting Guide � ������������������������������������������������������������������������������������������������������������������������������������������� 15 EC Declaration of Conformity ���������������������������������������������������������������������������������������������������������������������������������������������� 16 ABS reserves the right to alter specifications due to technical developments!
  • Page 3: Application Areas

    94/9C. Safety The general and specific Health and Safety requirements are described in detail in the Safety Instructions for ABS Products booklet. If anything is not clear or you have any questions as to safety make certain to contact the manufacturer ABS. �1 Use of explosion-proof pumps in explosive zones�...
  • Page 4: Technical Data

    Technical data Maximum noise level ≤ 70dB. This may be exceeded in certain circumstances. Detailed technical information is available in the technical data sheet ABS Piranha submersible grinder pump 08 - 125 which can be downloaded from www.absgroup.com > Downloads. 3�1...
  • Page 5: General Design Features

    Installation, Operating and Maintenance Instructions (Original Instructions) ABS Piranha submersible grinder pump S10 - PE125 General design features Submersible grinder pump fitted with a shredding system hydraulic. The shredding system is located before the impeller and consists of a shredding rotor in combination with a stationary cutting ring fixed to a spiral bottom plate.
  • Page 6: Design Features Piranha-Pe

    Installation, Operating and Maintenance Instructions (Original Instructions) ABS Piranha submersible grinder pump S10 - PE125 4� Design features Piranha-PE Submersible grinder pump fitted with a shredding system hydraulic and a Premium Efficiency motor. Pressure release screw Pressure release screw Upper bearing - single row Upper bearing - single row...
  • Page 7: Transport And Storage

    Installation, Operating and Maintenance Instructions (Original Instructions) ABS Piranha submersible grinder pump S10 - PE125 Transport and Storage 5�1 Transport During transport, care should be taken that the pump is not dropped or thrown. The unit is fitted with a lifting device to which a chain and shackle may be attached for transport purposes.
  • Page 8: Mounting And Installation

    Installation, Operating and Maintenance Instructions (Original Instructions) ABS Piranha submersible grinder pump S10 - PE125 Mounting and installation The regulations covering the use of pumps in sewage applications together with all regulations involving the use of explosion-proof motors should be observed.The cable ducting to the control panel should be sealed off in a gas-tight manner by the use of a foaming material after the cable and control circuits have been pulled through.
  • Page 9: Electrical Connection

    Installation, Operating and Maintenance Instructions (Original Instructions) ABS Piranha submersible grinder pump S10 - PE125 Electrical Connection Before commissioning an expert should check that one of the necessary electrical protective devices is available. Earthing, neutral, earth leakage circuit breakers, etc. must comply with the regulations of the local electricity supply authority and a qualified person should check that these are in perfect order.
  • Page 10: Wiring Diagrams

    Installation, Operating and Maintenance Instructions (Original Instructions) ABS Piranha submersible grinder pump S10 - PE125 7�3 Wiring diagrams Single phase: NOTE: NOTE: R = Run R = Run 60 Hz: 60 Hz: R S C R S C S = Start S = Start 50 Hz: 50 Hz:...
  • Page 11: Checking Direction Of Rotation

    Installation, Operating and Maintenance Instructions (Original Instructions) ABS Piranha submersible grinder pump S10 - PE125 7�4 Checking direction of rotation When three phase units are being commissioned for the first time and also when used on a new site, the direction of rotation must be carefully checked by a qualified person.
  • Page 12: Commissioning

    When carrying out repairs, only original spare parts supplied by the manufacturer should be used. ABS warranty conditions are only valid provided that any repair work has been carried out in an ABS approved workshop and where original ABS spare parts have been used.
  • Page 13: Shredding System

    This is particularly so if sewage containing sand is being pumped. Regular inspection and care is recommended to ensure a long service life. The ABS service organisation would be pleased to advise you on any applications you may have and to assist you in solving your pumping problems.
  • Page 14: Bearings And Mechanical Seals

    Installation, Operating and Maintenance Instructions (Original Instructions) ABS Piranha submersible grinder pump S10 - PE125 9�5 Bearings and Mechanical Seals Piranha pumps are fitted with lubricated-for-life ball bearings. Shaft sealing is by means of double mechanical seals (Piranha-PE), and mechanical seal / lip seal (Piranha-S). ATTENTION! Once removed, bearings and seals must not be re-used, and must be replaced in an approved workshop with genuine ABS spare parts. 9�6 Maintenance of Lifting Stations in accordance with EN 1056�...
  • Page 15: Troubleshooting Guide

    Installation, Operating and Maintenance Instructions (Original Instructions) ABS Piranha submersible grinder pump S10 - PE125 Troubleshooting Guide Fault Cause Pump does not Moisture sensor shutdown. Check for loose or damaged oil plug, or locate and replace faulty mechanical seal / damaged o-rings. Change oil. Level control override.
  • Page 16: Ec Declaration Of Conformity

    Cardo Flow Solutions Roskildevägen 1, Box 210, S-210 22 Malmö, Sweden. Declare under our sole responsibility that the products, ABS Piranha submersible grinder pump S10 - PE15, to which this declaration relates, are in conformity with the following standards or other normative documents as defined by Machinery Directive 006/4/EC, EMC-Directive 004/108/EC, Low Voltage Directive 006/95/EC, ATEX 94/9/EC, Construction Products 89/106/EC� ABS Piranha submersible grinder pump S10 - PE110:...
  • Page 17 SERVICE LOG Pump Type: Serial No: Date Hours of Opera- Comments Sign tion...
  • Page 18 SERVICE LOG Date Hours of Opera- Comments Sign tion...
  • Page 19 SERVICE LOG Date Hours of Operation Comments Sign...
  • Page 20 Cardo Production Wexford Ltd., Clonard Road, Wexford, Ireland Tel. +353 53 91 63 200 Fax +353 53 91 42335. www.cardo.com...

Table of Contents