Sony TRINITRON KV-27V20 Service Manual page 20

Operating video
equipment
You can use the supplied remote commander to
operate Sony or non-Sony video equipment that has an
infrared remote sensor. For this operation, set the
manufacturer's code number.
EE A IT RS a eS I Si ELE,
Setting the manufacturer's code
VTR (FUNCTION)
0 - 9 buttons
ENTER
CODE SET
Press the CODE SET, VTR (FUNCTION), and 0-9
buttons to enter the manufacturer's code
number (see the chart), then press ENTER. For
example, to operate a Sony 8 mm VCR, press
CODE SET, VTR (FUNCTION), 3, 0, 2, and ENTER.
-— FUNCTION ——
q i *t fy Rh
34 | Operations
VCR manufacturer code numbers
Manufacturer Code number
Sony 301, 302, 303
Aiwa 338
Audio Dynamic 314, 337
Bell & Howell (M. Wards) 330, 343
Brocsonic 319
Canon 309, 308
Citizen 332
Craig 315, 302, 332
Curtis Mathis 304, 338, 309
Daewoo 341, 312, 309
DBX 314, 336, 337
Dimensia 304
Emerson 319, 320, 316, 317, 318
Fisher 330, 334, 335, 333
Funai 338
General Electric 329, 304, 309
Goldstar 332
Hitachi 306, 304, 305
Instant Replay 309, 308
JC Penny 309, 305, 304, 330, 314,
336, 337
Jvc 314, 336, 337
Kenwood 314, 336, 332, 337
LXI (Sears) 332, 305, 333, 334, 330,
335
Magnavox 308, 309
Marantz 314, 336, 337
Marta 332
Memorex 309, 335
Minolta 305, 304
Mitsubishi/MGA 323, 324, 325, 326
Multitech 325, 338, 321
NEC 314, 336, 337
Olympic 309, 308
Panasonic 308, 309, 306, 307
Pentax 305, 304
Philco 308, 309
Philtps 308, 309
Pioneer 308
Quasar 308, 309
RCA/PROSCAN 304, 305, 308, 309,
311, 312, 313
Realistic 309, 330, 328, 335, 324,
338
Sansui 314
Singer 315
Samsung 322, 313, 321
Sanyo 330, 335
Scott 312, 313, 321, 335, 323,
324, 325, 326
Sharp 327, 328
Shintom 315
Signature 2000 (M. Wards) 338, 327
Sylvania 308, 309, 338
Symphonic 338
Tashiro 332
Tatung 314, 336, 337
Teac 314, 336, 338, 337
Technics 309, 308
Toshiba 312, 311
Wards 327, 328, 335, 331, 332
Yamaha 330, 314, 336, 337
Zenith 331
Notes
« If more than one code number is listed, try entering them one
by one, until you come to the correct code for your equipment.
* In some rare cases, you may not be able to operate your non-
Sony video equipment with the supplied remote commander.
This is because your equipment may use a code that is not
included with this remote commander. In this case, please use
the equipment's own remote control unit.
The code numbers for Sony equipment are assigned at the
factory as follows.
VHS VCR 301 (preset code for the supplied
remote commander)
8mm VCR 302
Beta, ED Beta VCRs 303
Whenever you remove the batteries — to replace them, for
example — if too much time is taken, the code number may
revert to the factory setting and must be reset.
.
Operating video equipment
VTR (POWER)
VTR (FUNCTION)
Video operating
buttons
0-9 buttons
ENTER
CH +/~
Use the video operating buttons on the remote
commander to operate the video equipment.
Press VTR (FUNCTION) before operating the
video equipment.
Operating a VCR Buttons on the remote
commander
Press VTR (POWER).
Press the 0 ~ 9 buttons.
To turn on or off
To select a channel
directl
To change channels Press CH +/-
To record Press B while pressing @. First release
B, then release @.
To play Press
To stop Press @
To fast forward Press >>.
To rewind the tape Press <4.
To pause Press ff
To resume normal playback, press again.
Press P® or 4 during playback
To resume normal playback, release the
button
Press TV/VTR
To search the picture
forward or backward
To change input mode
Note
+ Ifthe video equipment does not have a certain function, the
corresponding button on this remote commander wil! not
operate.
ea AP we
Turning off the system
@ KV-27V25/27V35/29V35CI29 V6S5MI29V75MI32V25/
32V35/24V35CIZ5V35/35V45/35V75 only
You can turn off the TV and Sony equipment with the
S-Link function, such as a VCR, together when you
make the S-Link connection (see page 10 for the
connection).
Press SYSTEM OFF.
SYSTEM OFF
Operations | 35