Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for INSIGHT DLP SENSOR 310
Summary of Contents for INSIGHT DLP SENSOR 310
- Page 1 INSIGHT DLP SENSOR 310, 310NTC & 310NTF Appliance Hardware Installation Guide...
-
Page 2: Table Of Contents
Front Panel Operation ............INSIGHT DLP SENSOR 310, 310NTC & 310NTF Appliance Hardware Installation Guide www.insightdlp.com... -
Page 3: Safety Notice And Warnings
AC input voltage: 100 - 240 V (auto-range) Input frequency range: 50/60 Hz Rated input current: 100 - 140V 8.0 6.0A 200 - 240V 4.5 3.8V INSIGHT DLP SENSOR 310, 310NTC & 310NTF Appliance Hardware Installation Guide www.insightdlp.com Page 3... -
Page 4: Site Preparation
Install near appropriate AC outlets, and Ethernet hubs or individual jacks. Be sure to install an AC Power Disconnect for the entire rack assembly. The Power Disconnect must be clearly marked. Ground the rack assembly properly to avoid electrical shock. INSIGHT DLP SENSOR 310, 310NTC & 310NTF Appliance Hardware Installation Guide www.insightdlp.com Page 4... -
Page 5: Unpacking The 4-Post Rack Installation Assemblies
Adjustable rear quick-mount rack rail assembly (attaches to the front of the rack) (attaches to the rear of the rack) Quick-mount rack rail assembly, outside view INSIGHT DLP SENSOR 310, 310NTC & 310NTF Appliance Hardware Installation Guide www.insightdlp.com Page 5... -
Page 6: 4-Post Rack Installation With Standard Rails
INSIGHT DLP SENSOR 310, 310NTC & 310NTF Appliance Hardware Installation Guide www.insightdlp.com Page 6... -
Page 7: 4-Post Rack Installation With Quick Mount Rails (Square Hole Rack Only)
Repeat these steps for the other side of the rack.* alignment for appliance installation. INSIGHT DLP SENSOR 310, 310NTC & 310NTF Appliance Hardware Installation Guide www.insightdlp.com Page 7... -
Page 8: Installing The Appliance In The 4-Post Rack
Two 10-32 x 3/4” Fixed chassis rail slide it out supporting the Phillips flat-head screws* (attached prior to shipment) unit on both sides at all times. INSIGHT DLP SENSOR 310, 310NTC & 310NTF Appliance Hardware Installation Guide www.insightdlp.com Page 8... -
Page 9: Unpacking The 2-Post Rack Installation Hardware
A pair of 2-post rack assemblies that attach directly to the rack 2 Post Rack rail assembly, inside view 2 Post Rack rail assembly, outside view INSIGHT DLP SENSOR 310, 310NTC & 310NTF Appliance Hardware Installation Guide www.insightdlp.com Page 9... -
Page 10: 2-Post Rack Installation
Tighten each of the single screws on the small fixed brackets (located on either side of the rack) to secure the brackets in the rack and ensure appliance stability. INSIGHT DLP SENSOR 310, 310NTC & 310NTF Appliance Hardware Installation Guide www.insightdlp.com Page 10... -
Page 11: Installing The Appliance In The 2-Post Rack
Carefully slide it out supporting the unit on both sides at all times. INSIGHT DLP SENSOR 310, 310NTC & 310NTF Appliance Hardware Installation Guide www.insightdlp.com Page 11... -
Page 12: Rear Panel Connections
USB Port 3 (generation 3) eth3 Port USB Port 4 (generation 3) DLP Port eth4 Port SPAN Port eth5 Port MGMT Port VGA Port RAID Controller Card INSIGHT DLP SENSOR 310, 310NTC & 310NTF Appliance Hardware Installation Guide www.insightdlp.com Page 12... - Page 13 In normal operation the Power Good LED on Power Supply Module 1 and Module 2 will be SOLID GREEN. If the power is down, both LEDs will BLINK GREEN. INSIGHT DLP SENSOR 310, 310NTC & 310NTF Appliance Hardware Installation Guide www.insightdlp.com Page 13...
-
Page 14: Front Panel Operation
/O Power replace the bezel. Button utton 2900 South Quincy Street Suite 330 Arlington, VA 22206 877-610-5625 877-605-8482 (F) www.insightdlp.com Copyright ©2017 Insight DLP. All rights reserved. INSIGHT DLP SENSOR 310, 310NTC & 310NTF Appliance Hardware Installation Guide www.insightdlp.com Page 14...