Using The Remote Control - Sony TRINITRON KV-20M20 Service Manual

; Step 2: Using the Remote Control
Step 3: Setting up Your Channels
Instructions in this manual are based on using the remote
control. You can also use the controls on the TV.
The menu illustrations are from KV-20M20. When features
found on other models are discussed, the manual lists the
models covered by that specific set of menus.
Note
* The menu disappears 90 seconds after you press a button, or
immediately after you press MENU.
Inserting Batteries
HUA
Insert two size AA (R6) batteries (supplied) by matching the
+ and — on the batteries to the + and - inside the battery
compartment. With normal use, the batteries should last for
approximately six months.
Notes
Remove the batteries to avoid possible damage from battery leakage
if you will not be using the remote control for an extended period of
time.
Handle the remote control with care. Avoid dropping it, getting it
wet, or placing it in direct sunlight, near a heater, or where the
humidity is high.
Changing the Menu
Language
Mh
ELLER SI EU
Except Canadian models
If you want to view the menus in Spanish, you can change the
menu language.
4 Press MENU. The
Main menu appears.
MENU
&@ Press A+ or Y-to
move the cursor (>) (x)"
to ENGLISH and press {44
RETURN. Wh
ENGLISH will
turn red.
4 Press A+ or V-
to select (x)" VIGEO
ESPANOL and = eeyToxr: ch
press RETURN. @ ty » ESPANOL
=e me
4 Press MENU to return to the TV program.
Note
* Some parts of the Spanish menus will appear in English.
; jonUOCD e,0UIDy a4y BuIsN » W9xshs oIpny Ue Bunrauu0> « Japsonwes e BunreuuED
a
n
—
a
cy
©
oo
2
a
0
2S
a
wi
'
ia
ey
7}
5
oe)
"8
ed
how
=
parts)
=F
Of.
os
_a
ou
(oO
2
Setting Cable TV On or
If you have connected the TV to a cable TV system, set CABLE to
ON. If not, set CABLE to OFF.
4 Press MENU.
2 Move the cursor to SET UP and press RETURN.
3 Move the cursor to CABLE and
press RETURN.
SET UP
»CABLE: ON
AUTO PROGRAM
CHANNEL ERASE/ADD
CHANNEL BLOCK
CHANNEL GUIDE
MENU
Use Yi RETRY Exit Few)
SET UP
4& Press A+ or V- to select ON or OFF.
»CABLE: OFF
AUTO PROGRAM
3 Press RETURN.
CHANNEL ERASE/ADD
& Press MENU to return to the TV CHOAREL BLOCK
program. SMENU
Use ¥ } RET] Exit fe)
Note
* If the screen is black, the TV is set to a video input and you cannot select
CABLE. Press TV/VIDEO until a channel number appears, then follow
steps 1-6.
Auto Programming Your Channels
TV channels can be preset easily. First, you can store all the
receivable channels automatically. Later, you can erase unwanted
channels or add additional channels.
Notes
* If the TV is set to VIDEO, you cannot run AUTO PROGRAM. Press
TV/VIDEO on the remote control until a channel number appears.
* Itis usually best to preset channels during the day when the greater
number of channels are broadcasting.
4+ Press MENU. The Main
menu appears. MENU
> VIDEO
SET UP
(Eq\/TEXT: CCI
ENGLISH
Use Yi RETRY) Exit [ew]
2 Press A+ or V-on the SET UP
remote control to move (R) PCABLE: ON
AUTO PROGRAM
the cursor (P) to SET UP. (x) HAAN ERASE/ADD
Press RETURN. Za CHANNEL GUIDE
The SET UP menu appears. anew
Use ¥ i (ETA) Exit feu]
& Press A+ or V- to move the cursor to AUTO PROGRAM and
press RETURN.
AUTO PROGRAM appears on the screen and the TV starts
scanning and presetting channels.
When all of the receivable channels are stored, AUTO
PROGRAM disappears.
Note
* AUTO PROGRAM will tune in all of the channels in your area, including
some with weak or scrambled signals. They will appear fuzzy on the
screen. You can erase them using CHANNEL ERASE/ADD.