Basic Operation - Gaggenau 200 Series User Manual And Installation Instructions

Basic operation

7 Basic operation
7.1 Switching on the appliance
Requirement: Align the remote control as precisely as
possible to the infrared receiver for the LED display.
Press to switch on the appliance.
▶
a The appliance starts at fan setting 2.
a The LED for the set fan setting lights up in the LED
display.
7.2 Switching off the appliance
Switch the appliance off when you are not using it.
Press to switch the appliance off.
▶
a The appliance switches off. Any functions currently
in progress are cancelled.
7.3 Selecting a fan setting
Press ⁠ or ⁠ .
▶
a The LED for the set fan setting lights up in the LED
display.
7.4 Switching on intensive mode
If particularly strong odours or vapours develop, you
can use intensive mode.
⁠ so oft drücken, bis in der LED-Anzeige die LED 4
1.
für die Intensivstufe 1 leuchtet.
⁠ so oft drücken, bis in der LED-Anzeige die LED 5
2.
für die Intensivstufe 2 leuchtet.
a After approx. 6 minutes, the appliance automatically
switches to fan setting 3.
7.5 Switching off intensive mode
To select a fan setting of your choice, press
▶
7.6 Switching on intermittent ventilation
With interval ventilation, the ventilation switches on for
approx. 6 minutes every hour.
Note: In the Home Connect app, you can set the time
and fan setting individually.
Press ⁠ .
▶
a In the LED display, LED 6 flashes continuously, the
LED for the selected fan setting lights up on the ap-
pliance.
a As soon as the ventilation time ends, the LED for
the fan setting you have selected goes out. LED 6
continues to flash.
7.7 Switching off interval ventilation
Press ⁠ .
▶
7.8 Switching on automatic mode
The optimum fan setting is set automatically using a
sensor.
1
Depending on the appliance specifications
Press ⁠ .
▶
a In the LED display, LED 6 lights up for automatic
mode.
7.9 Switch off automatic mode
Press ⁠ .
▶
a The appliance switches to the fan setting that was
previously set.
a The ventilation is automatically ended when the
sensor detects no further change in the room air
quality.
a Automatic mode runs for a maximum of four hours.
7.10 Sensor sensitivity
In automatic mode, a sensor in the appliance detects
the intensity of the cooking odours and roasting
odours. Depending on the setting of the sensor sensit-
ivity, the optimum fan setting is automatically switched
on.
If the sensor control reacts too weakly or too strongly,
you can change the setting for the sensor sensitivity.
¡ Default setting: Fan setting 3
¡ Lowest setting: Fan setting 1
¡ Highest setting: Fan setting 5
7.11 Setting the sensor sensitivity
Requirement: The appliance is switched off.
Press and hold
1.
Press
2.
To cancel the setting, press ⁠ .
To save the setting, press and hold
3.
prox. three seconds.
⁠ .
Or wait approx. 10 seconds until the setting is
saved automatically.
a A signal tone sounds as soon as the selected set-
ting is saved.
7.12 Saturation indicator
If the grease filters or odour filters are saturated, cor-
responding symbols flash after the appliance is
switched off.
Note: You can set the saturation indicator in the Home
Connect app depending on the filter used.
Clean the saturated grease filters and, in doing so, ob-
serve the cleaning instructions in these instructions.
Change the saturated odour filters and observe the in-
structions in the accompanying instructions.
If odour filters can be regenerated, follow the instruc-
tions in the accompanying instructions.
7.13 Setting the saturation indicator
1
The saturation indicator must be adjusted depending
on the filter used.
Requirement: The appliance is switched off.
Press and hold
1.
1
⁠ and ⁠ for approx. 3 seconds.
⁠ or to change the setting.
⁠ and ⁠ for approx. three seconds.
Basic operation en
1
1
⁠ and for ap-
27