When To Use Which Feature; Operation Mode And Temperature Setpoint; To Start/Stop Operation Mode And To Set The Temperature; Airflow Rate - Daikin FTXP20N5V1B9 Operation Manual

(b)
Condensation and water dripping might occur if the unit runs
outside its operation range.
5.2

When to use which feature

You can use the following table to determine which features to use:
Feature
Basic features
To start/stop the system and to set the
Operation modes and
temperature:
temperature
▪ Heat up or cool down a room.
▪ Blow air in a room without heating or
cooling.
▪ Decrease the humidity in a room.
▪ In Automatic mode, automatically
select an appropriate temperature
and operation mode.
To adjust the airflow direction (swing or
+ Airflow
fixed position).
direction
To adjust the amount of air blown into

Airflow rate

the room.
To run more quietly.
Advanced features
To use the system when you are also
Econo
using other power-consuming
appliances.
To save energy.
To provide a comfortable airflow that
Comfort
does NOT come in direct contact with
people.
To cool down or heat up the room
Powerful
quickly.
To automatically turn ON or OFF the
ON timer +
system.
OFF timer
5.3 Operation mode and temperature
setpoint
When. Adjust the system operation mode and set the temperature
when you want to:
▪ Heat up or cool down a room
▪ Blow air in a room without heating or cooling
▪ Decrease the humidity in a room
What. The system operates differently, depending on the user
selection.
Setting
The system cools down or heats up a
Automatic
room to the temperature setpoint. It
automatically switches between cooling
and heating if necessary.
The system decreases the humidity in a
Drying
room.
The system heats up a room to the
Heating
temperature setpoint.
The system cools down a room to the
Cooling
temperature setpoint.
The system only controls the airflow
Fan
(airflow rate and airflow direction).
The system does NOT control the
temperature.
FTXP20~35N5V1B9 + ATXP20~35N5V1B9
R32 Split series
3P717028-5D – 2023.08
Tasks
Description
Additional info:
▪ Outside temperature. The system's cooling or heating effect
decreases when the outside temperature is too high or too low.
▪ Defrost operation. During heating operation, frost might occur on
the outdoor unit and decrease the heating capacity. In that case,
the system automatically switches to defrosting operation to
remove the frost. During defrosting operation, hot air is NOT
blown from the indoor unit.
5.3.1 To start/stop operation mode and to set
the temperature
: Operation mode = Automatic
: Operation mode = Drying
: Operation mode = Heating
: Operation mode = Cooling
: Operation mode = Fan only
: Shows the set temperature.
1 Start operation by pressing one of the following buttons.
Mode Press
Automatic operation
Cooling operation
Drying operation
Heating operation
Fan only operation
2 Press or on the
temperature. You CANNOT adjust the temperature in drying or
fan only operation mode.
Cooling Heating
operation operation
18~32°C 10~30°C
3 Press to stop operation.
Result: The operation lamp goes off.
5.3.2 Airflow rate
1 Press to choose:
5 airflow rate levels, from "
Automatic airflow rate operation
Indoor unit quiet operation. When the airflow rate is
set to " ", the noise from the unit will be reduced.
INFORMATION
▪ If the unit reaches the temperature setpoint in cooling
or heating mode, the fan will stop operating.
▪ When using drying operation mode, you CANNOT
adjust the airflow rate setting.
To adjust the airflow rate
1 Press to change the airflow setting as follows:
5 Operation
Result
The operation lamp lights
up.
button one or more times to set the
Automatic Drying or fan
operation only operation
18~30°C —
" to " "
Operation manual
7