Wireless (Cordless) Measurement Using Electronic Flash Unit - Sekonic DIGI MASTER L-718 Operating Instructions Manual

Wireless (cordless) Measurement
using Electronic Flash Unit
In case the photographing subject is too far to use synchro cord, or in case
the synchro cord disturbs photographing, flash light can be measured
without connecting the cord.
(1) Switch the meter ON and set the
mode selection key at the position
I .
The symbol of
0
is indicated
on the display
(Fig .
13).
(2) Set the film speed (ISO) and shutter
speed (T) as shown in the
paragraphs for " Preparing the Meter
for Operation"
(3) Point the Lumisphare accurately
toward the camera from the subject
position, and press the measuring
switch. The symbol of
0
on the
display starts flashing
(Fig.
14).
(4) While the symbol is flashing (for
about 90sec.), fire the flash unit by
pressing its test button .
(5) The appropriate F-stop value is
displayed on the meter. The
measured value is indicated in dual
display by F-stop number with bar
symbols and bar-dot symbol marks
(Fig_ 15).
(6) If'the symbol of
0
is not flashing,
the meter can not accept wireless
flash measurement. Press the
measuring switch again to make the
meter ready for measurement.
< NOTE >
• If the measuring range is 'exceeded,
the digital F-stop number on the
display is replaced with either mark
of E.u. (and
,1)
for underexposure
or E.o. (and 0) for overexposure
(Fig_ 16).
• The display continues to indicate the
measured value for about 5 minutes
after measurement unless the
following measurement is made. After
this period of time the auto shut-off
circuit operates and turns the display
off.
(Ii)
ISO
Ina
I U
iii
n
H
_bO
u
-
1142284568 11
16 22 32 45 64 90
®_~_c. _~
(0 1
1111111 1) )
(Fig .
13)
-
~D~
ISO
In a
I U
iii
-
H n
_bO
u
-
1142284568 11 16 22 32 45 64 90
(Fig . 14)
0
ISO
Ina
IU
tB.O~~~HbO
C·············~1
1 1 4 2 2 8 4 5 6 8 1 16 22 32 45 64 90
(Fig . 15)
(Fi g . 16)
15
Wireless (cordless) Measurement
using Electronic Flash Unit
In case the photographing subject is too far to use synchro cord, or in case
the synchro cord disturbs photographing, flash light can be measured
without connecting the cord.
(1) Switch the meter ON and set the
mode selection key at the position
I .
The symbol of
0
is indicated
on the display
(Fig .
13).
(2) Set the film speed (ISO) and shutter
speed (T) as shown in the
paragraphs for " Preparing the Meter
for Operation"
(3) Point the Lumisphare accurately
toward the camera from the subject
position, and press the measuring
switch. The symbol of
0
on the
display starts flashing
(Fig.
14).
(4) While the symbol is flashing (for
about 90sec.), fire the flash unit by
pressing its test button .
(5) The appropriate F-stop value is
displayed on the meter. The
measured value is indicated in dual
display by F-stop number with bar
symbols and bar-dot symbol marks
(Fig_ 15).
(6) If'the symbol of
0
is not flashing,
the meter can not accept wireless
flash measurement. Press the
measuring switch again to make the
meter ready for measurement.
< NOTE >
• If the measuring range is 'exceeded,
the digital F-stop number on the
display is replaced with either mark
of E.u. (and
,1)
for underexposure
or E.o. (and 0) for overexposure
(Fig_ 16).
• The display continues to indicate the
measured value for about 5 minutes
after measurement unless the
following measurement is made. After
this period of time the auto shut-off
circuit operates and turns the display
off.
(Ii)
ISO
Ina
I U
iii
n
H
_bO
u
-
1142284568 11
16 22 32 45 64 90
®_~_c. _~
(0 1
1111111 1) )
(Fig .
13)
-
~D~
ISO
In a
I U
iii
-
H n
_bO
u
-
1142284568 11 16 22 32 45 64 90
(Fig . 14)
0
ISO
Ina
IU
tB.O~~~HbO
C·············~1
1 1 4 2 2 8 4 5 6 8 1 16 22 32 45 64 90
(Fig . 15)
(Fi g . 16)
15