Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for LawnMaster LMEBV260
Summary of Contents for LawnMaster LMEBV260
- Page 1 SAFETY AND OPERATING MANUAL PETROL BLOWER VACUUM LMEBV260...
-
Page 2: Table Of Contents
TABLE OF CONTENTS TECHNICAL DATA INTRODUCTIONS & SAFETY LABELS PARTS LISTING ASSEMBLY CONVERT TO BLOWER FUEL & OIL MIXTURE STARTING PROCEDURE WHEN ENGINE STARTS STARTING A FLOODED ENGINE MAINTENANCE & CARE STORAGE & REPLACEMENT PARTS TROUBLESHOOTING... -
Page 3: Technical Data
TECHNICAL DATA Thank you for purchasing the LawnMaster Petrol Blower Vacuum. This manual will explain the functions and use of the Blower Vacuum. Please read this manual carefully before operating the unit. MODEL LMEBV260 Dimensions 340x270x370 Engine Type 1E34FB Displacement... -
Page 4: Introductions & Safety Labels
A statement proceeded by word “NOTE” contains information that is handy to CAUTION! know and may make your job easier. LMEBV260 is equipped with a spark-arresting muffler. Do not operate the Read and follow this manual. unit without either muffler and spark arres-... -
Page 5: Parts Listing
PRODUCT DESCRIPTION If you have any question regarding your The instructions outlined in this manual is LMEBV260 Blower Vacuum, contact your a helpful resource to help you maximise local LawnMaster Service Dealership or the use and preserve the quality and contact Steelfort. -
Page 6: Assembly
ASSEMBLY 6. Push the ‘elbow tube’ in and rotate anti-clockwise until the locking screw 1. Unscrew the knob on the vacuum inlet holes are aligned. cover. The screw should remain on the cover at all times. 7. Screw M5x10 into place to secure elbow tube and catching bag. -
Page 7: Convert To Blower
CONVERT TO BLOWER Upper Handle & On/ Off Switch Throttle Blower Outlet CONVERT TO BLOWER Vacuum Inlet Cover The following instructions is to convert the Blower Vacuum from vacuum to a Starter Cord blower unit. Ensure the unit is switched off Cleaner Cover and the catching bag is empty. -
Page 8: Fuel & Oil Mixture
FUEL & OIL MIXTURE Be careful, a wrong mixture of the fuel will cause machine failure. WARNING Petrol Do not fill the fuel tank to the brim and Use 91 Unleaded Petrol. also do not add fuel to the tank in a closed non-ventilated area. -
Page 9: Starting Procedure
Never smoke or light any fires near the Do not pull the starter cord to its full blower or fuel and only transport and store length. fuels in an approved container! Always engage the starter before cranking Never place flammable maternal close to the engine. -
Page 10: When Engine Starts
WHEN THE ENGINE STARTS MAINTENANCE & CARE IMPORTANT WARNING For maximum vacuum performance and Before performing any maintenance operating life, allow the engine to warm-up on this machine, stop the engine and before use. disconnect the spark plug wire! 1. Run the engine at idle speed until Inspect the engine, tank and hose for operating temperature is reached (2 to 3 possible fuel leaks, and repair as... -
Page 11: Storage & Replacement Parts
3. Install the spark plug finger-tight in the STORAGE (30 DAYS OR LONGER) cylinder head, and then tighten it firmly with the spark plug wrench. If a torque CLEANING wrench is available, torque the spark plug Thoroughly clean the machine exterior. to 148-165 inch pounds. -
Page 12: Troubleshooting
Steelfort 500 Rangitikei Street Private Bag 11045 Palmerston North, 4442, New Zealand 06 350 1350 | steelfort.co.nz Steelfort Auckland 880 Great South Road, Penrose SCAN TO VIEW THE Auckland, 1061, New Zealand LAWNMASTER RANGE 09 573 1324 | outlet@steelfort.co.nz steelfortnz...
Need help?
Do you have a question about the LMEBV260 and is the answer not in the manual?
Questions and answers