Advertisement
Available languages
Available languages
TABLE OF CONTENTS
Dishwasher Safely.........ccccccsssccccsssssscccssssssscccssesscccsceens 2-3
4
Materials supplied
Pre-install instructions
Inlet Water connections
8
9
9
Leveling the Dishwasher...
s s s s s s s s s s s s e s s s s c e s c e s e s e e s e e s e c e o r e n s e e e s 10
Attaching the Toe Panel .0..
te eeccceeescores
c e c e c e e r e c e o r e c e o r e e c e e e e s 11
IMPORTANT SAFETY INSTRUCTIONS
To avoid possible injury or property damage, OBSERVE ALL
WARNINGS
AND CAUTIONS. These instructions are intend-
ed for use by qualified installers only. In addition to these
instructions, the dishwasher shall be installed to meet all
electrical and plumbing codes and ordinances (both national
and local).
A
Avoiding General Hazards
Do not use the dishwasher until it is completely installed. When
opening the door on an uninstalled dishwasher, carefully open
the door while supporting the rear of the unit. Failure to follow
this warning can cause the dishwasher to tip over and result
in serious injury.
WARNING
In some conditions, hydrogen gas can form in a hot water system
that has not been used for weeks. Hydrogen gas is explosive.
Before filling a dishwasher from a system that has been off for
weeks, run the water from a nearby faucet in a well ventilated
area until there is no sound or evidence of gas.
Temperatures required for soldering and sweating will damage
the dishwasher's base and water inlet valve. If plumbing lines
are to be soldered or sweated, keep the heat source at least
6 inches (152.4 mm) away from the dishwasher's base and
water inlet valve.
Removing any cover or pulling the dishwasher from the cabinet
can expose hot water connections, electrical power and sharp
edges or points. Handle with care. Always wear gloves and
safety glasses.
Avoiding Electrical Shock/Fire Hazards
Do not allow the electrical and water supply lines to touch.
Separate channels are provided under the dishwasher.
Do not work on an energized
circuit. Doing
so could result
in serious injury or death. Only qualified electricians should
perform
electrical
work.
Do not attempt
any
work on the
dishwasher electric supply circuit until you are certain the circuit
is de-energized.
Make sure electrical work is properly installed. There
should be no loose electrical connections. Ensure all
electrical connections are properly made.
The customer has the responsibility of ensuring that the
dishwasher electrical installation is in compliance with all
national and local electrical codes and ordinances. The
dishwasher is designed for an electrical supply of 1 20V,
60 Hz, AC, connected to a dishwasher-dedicated, properly
grounded electrical circuit with a fuse or breaker rated for
15 amps. Electrical supply conductors shail be a minimum
#14 AWG
copper only wire rated at 75°C (167°F) or
higher.
This appliance must be connected to a grounded metal,
permanent wiring system, or an equipment-grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminal or lead on
the appliance. Do not use extension cords.
Avoiding Plumbing/Scalding Hazards
Do not perform any work on a charged hot water line.
Serious injury could result. Only qualified plumbers should
perform plumbing work. Do not attempt any work on the
dishwasher hot water supply plumbing until you are certain
the hot water supply is shut off.
Do not overtighten the 90° elbow. Doing so may damage
the water inlet valve and cause a water leak.
Temperatures required for soldering and sweating will
damage the dishwasher's water inlet valve. If plumbing
lines are to be soldered or sweated, keep the heat source
at least 6 inches (152.4 mm) away from the dishwasher's
water inlet vaive.
Check local plumbing codes for approved plumbing
procedures and accessories. All plumbing should be done in
accordance with national and local codes.
These instructions depict an installation method for stainless
steel braided hose or PEX hot water supply lines. If using
copper tubing or other material for water supply, defer to
a licensed plumber for proper installation.
Advertisement
