Table of Contents
Advertisement
8.7 Refilling the water tank
If the water tank runs dry during operation, steaming
will be paused.
Open the appliance door carefully.
1.
Remove the water tank from the tank recess.
2.
Fill the water tank with water.
3.
Insert the full water tank back into the tank recess.
4.
Close the appliance door.
5.
8.8 Setting the type of heating and the
temperature
Press the type of heating that you want to use.
1.
Set the temperature using
2.
adjustment bar.
If required, you can implement additional settings:
– Time-setting options → Page 11
Press
to start the operation.
3.
a The appliance starts heating.
a The setting values and how long the appliance has
already been in operation are shown on the display.
When the food is ready, use
4.
ance off.
Note: The most suitable type of heating for your food
can be found in the description of the type of heating.
→ "Types of steam heating", Page 6
Changing the type of heating
When you change the type of heating, the other set-
tings are also reset.
Press
.
1.
Press
.
2.
Press the type of heating that you want to use.
3.
Reset the operation and use
4.
Changing the temperature
Once the operation has started, you can change the
temperature at any time.
Press the temperature.
1.
9 Time-setting options
For an operation, you can set the cooking time and the
time at which the operation should be finished. The
timer runs independently of the operation.
Time-setting
Use
option
Cooking time
If you set a cooking time, the appli-
ance stops heating automatically
once this time has elapsed.
End time
Along with the cooking time, you can
set the time at which you want the
operation to end. The appliance
starts up automatically so that the
operation finishes at the required
time.
Timer
You can set the timer to run inde-
pendently of the appliance during op-
eration. It does not affect the appli-
ance.
or
, or directly via the
to switch the appli-
to start.
Change the temperature using
2.
via the adjustment bar.
Press "Apply".
3.
8.9 "Fill water tank" message
If you select a type of heating and the water tank is
only half full, the appliance displays the message "Fill
water tank".
If the water tank contains sufficient water for cooking,
start the appliance.
If the water tank does not contain sufficient water for
cooking, fill the water tank.
→ "Filling the water tank", Page 10
8.10 After using the Steam function
When you use the appliance, moisture and food rem-
nants remain in the cooking compartment afterwards.
Dry and clean the appliance after each use. Empty the
water tank.
After using the Steam function
Dry the cooking compartment.
1.
→ "Drying the cooking compartment", Page 19
Empty the water tank.
2.
→ "Emptying the water tank", Page 19
8.11 Displaying information
In most cases, you can call up information about the
function that you have just started. The appliance auto-
matically displays certain information, e.g. to ask you to
do/confirm something or to issue a warning.
Press .
1.
a If information is available, this is displayed for a few
seconds.
If there is a lot of content in the tile, scroll using
2.
or
.
If required, close the notification using
3.
9.1 Setting the cooking time
You can set the cooking time for the operation of up to
24 hours.
Requirement: An operating mode and temperature
have been set.
Press "Cooking time".
1.
To set the cooking time, press the relevant time
2.
value, e.g. hour display "h" or minute display "min."
a The selected value is marked in blue.
Set the cooking time using
3.
the adjustment bar.
If required, use
to reset the setting value.
Press "Apply".
4.
Press
to start the operation.
5.
a The appliance starts to heat and the cooking time
counts down.
a When the time has elapsed, a signal sounds. A noti-
fication appears on the display confirming that the
operation has finished.
Once the cooking time has elapsed:
6.
Time-setting options en
or
, or directly
.
or
, or directly via
11
Advertisement
Table of Contents
