Table of Contents
Advertisement
en Basic operation
7.2 Carrying out the initial configuration
When the appliance is connected to the electricity sup-
ply for the first time or following a lengthy power cut,
you must configure the settings before you can use it. It
may take a few seconds for the settings to appear on
the display.
Note: You can also enter the settings using the Home
Connect assistant. In this case, press
last point in the initial configuration. If your appliance is
connected, follow the instructions in the app.
Setting the language
Use the rotary selector to select the required lan-
1.
guage.
Press .
2.
a The next setting appears.
Setting the time
Turn the rotary selector to set the current time.
1.
Press .
2.
a The next setting appears.
Setting the date
Use the rotary selector to set the current day.
1.
Press .
2.
Use the rotary selector to set the current month.
3.
Press .
4.
Use the rotary selector to set the current year.
5.
Press .
6.
Setting the water hardness
Use the rotary selector to set the hardness.
1.
Press .
2.
a A notification appears on the display confirming that
the initial configuration is complete.
7.3 Calibrating and cleaning the appliance
before using it for the first time
Calibrate the appliance and clean the cooking compart-
ment and accessories before using it to prepare food
for the first time.
Note: The boiling point of water depends on the air
pressure. During calibration, the appliance self-adjusts
during the first steam operation to the pressure ratio at
the installation location.
Do not open the appliance door while calibration is in
progress, as this will cancel the calibration process.
Requirement: The cooking compartment is cold or at
room temperature.
Remove the product information and the accessor-
1.
ies from the cooking compartment. Remove any
leftover packaging, such as polystyrene pellets, and
any adhesive tape either in or on the appliance.
8 Basic operation
8.1 Switching on the appliance
Press
to switch the appliance on.
▶
The
button lights up blue.
‒
a The Siemens logo appears in the display. A type of
heating and a temperature are then displayed.
12
2.
3.
4.
5.
to go to the
6.
a The calibration starts. This generates a lot of steam.
a When the cooking time has elapsed, a signal
7.
8.
9.
a When the cooking time has elapsed, a signal
10.
11.
12.
13.
Note: Following a power cut, the calibrated settings are
retained.
To adjust the appliance to a new installation location
after moving house, reset the basic settings to the fact-
ory settings. Carry out the procedures for initial start-up
and calibration again.
8.2 Switching off the appliance
Switch your appliance off when you are not using it.
The appliance will switch itself off automatically if it is
not used for a certain period of time.
▶
Wipe the smooth surfaces in the cooking compart-
ment with a soft, damp cloth.
Press
to switch the appliance on.
Fill the water tank.
Apply the following settings:
Type of heating
Temperature
Cooking time
→ "Basic operation", Page 12
Press
to start the operation.
Ventilate the kitchen while the appliance is heat-
‒
ing.
sounds and the duration is at zero on the display.
Allow the appliance to cool down and then dry the
cooking compartment floor thoroughly.
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures
above 120 °C, this will damage the enamel.
Do not use the appliance if there is water on the
▶
cooking compartment floor.
Wipe away any water on the cooking compart-
▶
ment floor before operation.
Apply the following settings:
Type of heating
Temperature
Cooking time
→ "Basic operation", Page 12
Press
to start the operation.
Ventilate the kitchen while the appliance is heat-
‒
ing.
sounds and the duration is at zero on the display.
Press
to switch the appliance off.
Once the appliance has cooled down, clean the
smooth surfaces in the cooking compartment with a
detergent solution and a dish cloth.
Clean the accessories thoroughly using a detergent
solution and a dish cloth or soft brush.
Empty the water tank and dry the cooking compart-
ment.
→ "Emptying the water tank", Page 17
Press
to switch the appliance off.
Steam
100 °C
30 minutes
4D hot air
Maximum
30 minutes
Advertisement
Table of Contents
