Table of Contents
Advertisement
7.1 Performing initial start-up
After connecting the appliance to the power supply,
you must configure the settings for its initial start-up. It
may take a few minutes for the settings to appear on
the display.
Note: You can also use the Home Connect app to con-
figure the settings. When your appliance is connected,
follow the instructions in the app.
Press
to switch the appliance on.
1.
a The first setting appears.
If required, change the setting.
2.
Possible settings:
– Language
– Home Connect
– Time
– Date
Use
to switch to the next setting.
3.
Work through the settings and make changes as re-
4.
quired.
a After the last setting, a message appears on the dis-
play confirming that the initial start-up is complete.
To check the appliance before heating for the first
5.
time, open and close the appliance door once.
7.2 Cleaning the appliance before using it
for the first time
Before using the appliance to cook food for the first
time, you must clean the cooking compartment and ac-
cessories.
Basic operation
8 Basic operation
8.1 Switching on the appliance
Press
to switch the appliance on.
▶
a The display shows the menu.
8.2 Switching off the appliance
Switch your appliance off when you are not using it.
The appliance automatically switches itself off if it is not
used for a certain period of time.
Press
to switch the appliance off.
▶
a The appliance switches off. Any functions currently
in progress are cancelled.
a The time or residual heat indicator appears on the
display.
8.3 Starting the operation
You must start each operation.
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures above
120 °C, this will damage the enamel.
Do not use the appliance if there is water on the
▶
cooking compartment floor.
Wipe away any water on the cooking compartment
▶
floor before operation.
Use
to start the operation.
▶
a The settings appear on the display.
Remove the product information and the accessor-
1.
ies from the cooking compartment. Remove any
leftover packaging, such as polystyrene pellets, and
any adhesive tape either in or on the appliance.
2.
Wipe the smooth surfaces in the cooking compart-
ment with a soft, damp cloth.
Press
to switch the appliance on.
3.
4.
Apply the following settings:
Type of heating
Temperature
Cooking time
→ "Basic operation", Page 13
Start the operation.
5.
Ventilate the kitchen while the appliance is heat-
‒
ing.
a Once the cooking time has elapsed, a signal tone
sounds. A note appears on the display confirming
that the operation has finished.
Press
to switch the appliance off.
6.
Once the appliance has cooled down, clean the
7.
smooth surfaces in the cooking compartment with a
detergent solution and a dish cloth.
Clean the accessories thoroughly using a detergent
8.
solution and a dish cloth or soft brush.
8.4 Interrupting the operation
You can interrupt the operation and then continue
again.
To interrupt the operation, press
1.
Press
again to resume operation.
2.
8.5 Setting an operating mode
After you have switched on the appliance, the menu
appears on the display.
To scroll through the various selection options,
1.
swipe to the left or right on the display.
To select a function, press the corresponding tile.
2.
a Depending on the function, possible adjustment val-
ues or other tiles are available for selection.
If required, press on another tile.
3.
To change the setting values:
4.
Press
or
.
‒
Or press
and enter the value directly via the
‒
number field that appears.
Press
to start the operation.
5.
If the operation is ended:
6.
If required, you can select other settings and re-
‒
start the operation.
When the food is ready, use
‒
pliance off.
Tip: You can save your settings as "Favourites"
use these again.
→ "Favourites", Page 20
Basic operation en
4D hot air
Maximum
1 hour
.
to switch the ap-
and
13
Advertisement
Table of Contents
