Pioneer VSX-D601 Operating Instructions Manual page 15

REAR PANEL FACILITIES
) PRE OUT jacks
[FRONT AMP]
When a separate power amplifier is used to drive the front speakers,
connect the power amplifier to these jacks.
{CENTER AMP]
When a separate power amplifier is used to drive the surround center
speaker, connect the power amplifier to this jack.
{REAR AMP]
When a separate power amplifier is used to drive the rear speakers,
connect the power amplifier to these jacks.
(3) CENTER SPEAKER terminals
Connect the center speaker to these terminals.
NOTE:
Da not allow any of the cord's conductors to protrude trom the terminals
or touch any other conductors. Malfunctioning or breakdowns may
occur when conductors come into contact with each other.
Use center speakers of impedance 8 2 — 16 Q.
(9) REAR SPEAKERS terminals
Connect the rear speakers to these terminals.
NOTE:
Do net allow any of the cord's conductors to protrude from the terminals
or touch any ather conductors. Maffunctioning or breakdowns may
occur when conductors come into contact with each other.
Use rear speakers of impedance 8 2 — 16 2.
(( FRONT SPEAKERS terminals
A: Connect te the first set.of speakers.
8: Connect to the second set of speakers.
Speaker lead wire preparation and connection.
NOTE:
Do not allow any of the cord's conductors to protrude from the terminals
or touch any other conductors. Malfunctioning or breakdowns may
occur when conductors come into contact with each other.
Use speakers of impedance 8 2 — 16 0.
@) PHONO input jacks
Connect to the output cables from a turntable.
@) GND terminal
Connect the turntable ground lead to this terminal.
@) CD input jacks
Connect to the output jacks of a compact disc player.
TV jacks {input}
Use these jacks if you wish to connect a TV tuner with both video and
audio outputs.
[VIDEO IN]
Connect the TV tuner's VIDEO OUTPUT to this jack.
[AUDIO IN (L, R}]
Connect the TV tuner's AUDIO OUTPUT to these jacks.
LD jacks
[VIDEO IN}
When watching the video image from an LD player, connect its VIDEO
OUTPUT jacks here.
[AUDIO IN (L, RIT
When playing back the audio channel from an LD player, connect its
AUDIO OUTPUT jacks here.
@ CONTROL IN/OUT jacks
IN: Connect this jack to other Pioneer components (main unit or
remote control unit) when using those components to control
this unit.
OUT: Connect this jack to other Pioneer components when using the
remote control of this unit to control the other components.
NOTE:
The receiver's rernote sensor does not function when a plug is inserted
in IN jack. To operate, point the remote control unit at the remote sensor
on the component to which the receiver's IN jack is connected.
When using the
MR-100
|
M-100
PS eee
ke
a a i
Receiver
oe
A. An a e s
Pioneer component
bearing the | mark.
control unit component bearing
the if] mark.
@ MULTI-ROOM REMOTE IN jack
Connect to the separately sold MR-100 Multi-Reom remote contro! unit.
@® AC OUTLETS
{U.S. and Canadian models]
[SWITCHED TOTAL 100 W (0.8 A) MAX}
Power supplied through these outlets is turned on and off by the
receiver's POWER switch. Total electrical power consumption of
connected equipment should not exceed 100 W {0.8 A).
{UNSWITCHED 100 W (0.8 A} MAX]
Power flows continually to this outlet, regardless of whether the receiver
is switched ON or OFF. Electrical power consumption of the connected
equipment should not exceed 100 W (0.8 A}
The equipment should be disconnected by removing the power plug
from the wall socket when not in regular use, e.g. when on vacation:
[Multi-voitage model]
SWITCHED TOTAL 100 W MAX
Power supplied through these outlets is turned on and off by the
receiver's POWER switch. Total electrical power consumption of
connected equipment should not exceed 100 W
UNSWITCHED 100 W MAX
Power flows continually to this outlet, regardiess of whether the receiver
is switched ON or OFF. Electrical power consumption of the connected
equipment should not exceed 100 VW
NOTE:
® This unit should be disconnected by removing the power plug from
the wall socket wher not in regular use, e.g. when on vacation.
° De not connect appliances with high power consumption such as
heaters, irons, or television sets to these AC OUTLETS in order to
avoid overheating and fire risk
This can cause the receiver to malfunction.
CAUTION: |
DO NOT CONNECT MONITOR OR TV SET.
@ Power cord
15
< ARBIG80 >
En