Related Manuals for ABB Tina 11A
Summary of Contents for ABB Tina 11A
- Page 1 Original instructions Tina 11A Connection block ABB AB / Jokab Safety Varlabergsvägen 11, SE-434 39 Kungsbacka, Sweden www.abb.com/lowvoltage...
- Page 2 DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall responsibility of ABB/JOKAB SAFETY for any act exceed the individual price of the product on which liability asserted.
-
Page 3: Table Of Contents
Testing of the safety functions ..........................9 Troubleshooting ..............................9 Operation ............................10 LED indication..............................10 Information output signal attributes ........................10 Technical data ........................... 11 Dimensions ..............................12 EC Declaration of conformity ......................13 2TLC172149M0201, rev. A www.abb.com/lowvoltage 2011-09-26... -
Page 4: Introduction
Introduction Scope The purpose of these instructions is to describe the connection block Tina 11A and to provide the necessary information required for installation and operation. Audience This document is intended for authorized installation personnel. Prerequisites It is assumed that the reader of this document has knowledge of the following: Basic knowledge of ABB/Jokab Safety products. -
Page 5: Overview
Overview General description Tina 11A is a connection block with two 5-pole M12 connectors. It is used to connect two safety devices with 5-pole M12 connectors to the dynamic safety circuit. This simplifies wiring and reduces cable costs. Several connection blocks can be connected to one Vital or Pluto. -
Page 6: Connections
NB: Shielded cable is recommended between this unit and the rest of the safety circuits. Caution! All cable colours according to ABB/Jokab Safety standard cables. Warning! The information channel output shall never be used for the safety purpose(s). 2TLC172149M0201, rev. A www.abb.com/lowvoltage... -
Page 7: Connection Examples
Connection examples Caution! All cable colours according to ABB/Jokab Safety standard cables. 2TLC172149M0201, rev. A www.abb.com/lowvoltage 2011-09-26... - Page 8 Caution! All cable colours according to ABB/Jokab Safety standard cables. 2TLC172149M0201, rev. A www.abb.com/lowvoltage 2011-09-26...
-
Page 9: Installation And Maintenance
(EN 62061:2005). In case of breakdown or damage to the product, contact the nearest ABB/Jokab Safety Service Office or reseller. Do not try to repair the product yourself since it may accidentally cause permanent damage to the product, impairing the safety of the device which in turn could lead to serious injury to personnel. -
Page 10: Operation
H) is given in the table below. Info output signal switch Delay ~ 95 ms ~ 80 ms Warning! The information output signal is not a failsafe signal and should never be used for the safety purpose(s). 2TLC172149M0201, rev. A www.abb.com/lowvoltage 2011-09-26... -
Page 11: Technical Data
Technical data Manufacturer Address ABB AB / JOKAB SAFETY Varlabergsvägen 11 SE-434 39 Kungsbacka Sweden Article number/Ordering data Tina 11A: 2TLA020054R1700 Power supply Operating voltage 24 VDC +15 %, -15 % Total current consumption 17 mA (27 mA with max information output) -
Page 12: Dimensions
Dimensions NB: All measurements in millimetres. 2TLC172149M0201, rev. A www.abb.com/lowvoltage 2011-09-26... -
Page 13: Ec Declaration Of Conformity
EC Declaration of conformity EC Declaration of conformity (according to 2006/42/EC, Annex2A) ABB AB declare that the safety components of ABB AB make with type designations and safety JOKAB SAFETY functions as listed below, is in conformity with the Directives Varlabergsvägen 11...