F&F WZE-3 Manual

Electricity consumption meter

Advertisement

Quick Links

WZE-3 RST
Electricity
consumption meter,
3-phase, resetable
Do not dispose of this device in the trash along with other waste!
According to the Law on Waste, electro coming from households free of charge and can
give any amount to up to that end point of collec� on, as well as to store the occasion of
the purchase of new equipment (in accordance with the principle of old-for-new, regard-
less of brand). Electro thrown in the trash or abandoned in nature, pose a threat to the
environment and human health.
Purpose
The WZE-3 RST is a 3-phase, 4-wire energy consumption indica-
tor equipped with an additional, resetable energy meter.
Functioning
A special electronic system under the influence of current flow
and applied voltage in each phase, generates pulses in propor-
tion to the electricity consumed in this phase. The sum of the
pulses of the three phases is indicated by a flashing LED shall
be converted to energy, taken throughout the three-phase sys-
tem, and its value is determined by the segment LCD display.
The digits after the decimal point represent hundredths (0.01
kWh = 10 Wh).
The indicator is equipped with a 1-row LCD display for displaying
total energy consumption, or energy consumption since the last
meter reset. The value of the resetable meter is symbolized on
the indicator by displaying the [r] sign on the first segment of
the display.
F&F Filipowski L.P.
Konstantynowska 79/81, 95-200 Pabianice, POLAND
phone/fax (+48 42) 215 23 83 / (+48 42) 227 09 71
www.fif.com.pl; e-mail: biuro@fif.com.pl
- 1 -

Advertisement

Table of Contents
loading

Summary of Contents for F&F WZE-3

  • Page 1 Electro thrown in the trash or abandoned in nature, pose a threat to the environment and human health. Purpose The WZE-3 RST is a 3-phase, 4-wire energy consumption indica- tor equipped with an additional, resetable energy meter. Functioning...
  • Page 2: Pulse Output

    To switch between the display of the resetable and total meter, briefly press the button located on the front. To return to the total energy meter, briefly press the button on the front again. To switch, do not hold down the button because this will reset the auxiliary counter to zero.
  • Page 3 Number of the meter The meter is marked with an individual factory number to enable its unambiguous identification. The marking is indelible (laser engraving). Sealing The meter has the option of sealing the input and output termi- nals, preventing the meter from being bypassed.
  • Page 4: Front Description

    Front description Mounting 1. Disconnect power supply. 2. Mount meter on a rail in distribution box. 3. Open terminal covers. 4. Connect the power supply to the terminals 1 (L1 IN), 3 (L2 IN), 5 (L3 IN). 5. Connect the circuit to be measured or a single receiver to the terminals 2 (L1 OUT), 4 (L2 OUT), 6 (L3 OUT).
  • Page 5: Terminals Description

    Dimensions Terminals description 1, 3, 5 – L1, L2, L3 (power supply) 2, 4, 6 – L1, L2, L3 (reception) – neutral wire (input) – neutral wire N (output) max. 80 A ! – pulse output (+) – pulse output (–) - 5 -...
  • Page 6: Wiring Diagram

    Wiring diagram - 6 -...
  • Page 7 Technical data instalation 3-phase, 4-wire reference voltage 3×230/400 V minimum detection current 0.02 A base current 3×5 A maximum current 3×80 A voltage measurement range 160÷265 V accuracy class (IEC62052-11 i IEC62053-21) 1st class rated frequency 50 Hz insulation protection class housing ABS material energy consumption of the meter...
  • Page 8: Warranty

    Warranty F&F products are covered by a 24-month warranty from the date of purchase. The warranty is only valid with proof of purchase. Contact your dealer or contact us directly. CE declaration F&F Filipowski L.P. declares that the device is in conformity with the essential requirements of the Low Voltage Directive (LVD) 2014/35/EU and the Electromagnetic Compatibility (EMC) Directive 2014/30/UE.

This manual is also suitable for:

Wze-3 rst

Table of Contents