Operation To Reset - Kenwood 106VR Instruction Manual

1O6VR / 1 O5VA [En)
Operation to reset
normal condition.
Amplifier
The STANDBY indicator blinks and sound is
not output.
The microcomputer may fall into malfunction (impossibility to
operate, erroneous display, etc.) when the power cord is unplugged
while power is ON or due to an external factor. In this case, execute
the following procedure to reset the microcomputer and return it to
@ The speaker cords are disconnected.
@e MUTE is ON
(The MUTE ON indicator is blinking}
e The SPEAKERS keys are set to OFF
e The TAPE 2 MONITOR key is set to ON
e Speaker cords are short-circuited.
Sound is not output from one of the speak-
ers.
Sound is not output from the surround
speaker and/or center speaker, or their sound
is very small.
A hum noise is generated when the PHONO
input is selected.
System contro! is not available when TAPE1
or MD is selected.
System control is not available.
Tuner
Radio stations cannot be received.
Interference.
A station which was preset cannot be re-
ceived by pressing the corresponding nu-
meric key.
1 Unplug the AC power plug from the wall outlet.
2 While holding the POWER switch depressed, piug the AC
plug into the power outlet.
Please note that resetting the microcomputer clears the contents
stored in and returns to the condition when it left the factory
below to see if the problem can be corrected before seeking help from your dealer or service representative.
e@ Connect them properly referring to "Connec-
tion of speakers". 6,
e Press the MUTE key to OFF. 115
12
~
e Set the SPEAKERS key to GN.
@Set the TAPE 2 MONITOR key to OFF.
Set the input selector to the position other than
tuner.
@ Turn the power off, eliminate the short-circult-
6
e The speaker cord Is disconnected.
eThe BALANCE controt is set to an extreme
position.
cord are d:sconnected.
@ The Surround play mode has not been engaged.
e@ The surround and center speaker leveis are set to
tne minimum positions.
@ The audio cord from the turntable 1s not inserted
securely mto the PHONO jacks.
e The turntable is not grounded.
e@ "TAPE" or "MD" is not displayed.
e@ The XS8 and SL16 modes were switched while
the AC plug is left plugged into the wall power
outlet
@No antenna 's connected.
e The broadcast band |s not set properly.
e Fhe frequency of the desired station Is not tuned.
@ Noise due to ignition noise of an automobile.
e@ Noise due to ar. influence from an electric appli-
ance
e@ Noise due to anearby TV set.
e@ The preset stateon belongs to a frequency that
cannot be rece-ved
eThe preset memory was cleared because the
power cord had been unplugged for along period
of me.
@ihe TUNER inout is not selected.
@ Tne surround speaker cords and/or center speaker
® Connect it properly referring to "Connection of
speakers". ae
@ Adjust the Left/Right balance. ~ 13,
_
@ Connect them properly referring to "Connec-
tion of speakers". =! 6.
@ Set the presence mode. 122.
@ Adjust the surround and center speaker levels.
@ insert the audio cord plugs securely into the
PHONO Jacks. 4.
e Connect the grounding wire to the GND termi-
nal on the rear panel.
@ Switch the display to TAPE TorMD
wld. 16,
e@ Unplug the AC plug from the wall outlet and
switch the XS8 or SL16 mode as required. _
Adjust the brightness with the DISPLAY key
~
aS
@ Connect an antenna.
@ Set the broadcast band properly.
@ Tune the frequency of the desired Station,
nea
~3r
= 17
cee
elnstall the outdoor antenna away from the
road.
e Turn off the power to the appliance.
elnstal! the system farther away from the TV
set
@ Preset a station with a receivable frequency.
- 12.
e Preset the station again.
@ Select the TUNER input.