Čeština - Philips Aqua Plus 8000 Series Manual

Problem
The suction power does not feel stable.
The Floor Type Recognition is not
reacting logically.
The appliance delivers static shocks.
Using the water tank
Problem
The water flow from the water tank is
reduced.
The appliance has a lower suction
power than usual.
Too much water flows out of the water
tank at a too high speed.
The floor dries with stripes.
Čeština
Čeština
Důležité bezpečnostní informace
Před použitím přístroje a jeho příslušenství si pečlivě přečtěte tuto příručku s důležitými informacemi a uschovejte ji pro budoucí použití. Dodané
příslušenství se může pro různé výrobky lišit.
Nebezpečí
- Nikdy nevysávejte vodu nebo jinou tekutinu, hořlavé látky ani popel.
Possible cause
Nothing is wrong. This is the feature of
"Floor Type Recognition" being triggered.
Your appliance is detecting the floor type
and cleaning with an optimized
performance for that floor.
The filter and the cyclone are dirty.
The brush is clogged with hair or dirt.
The Vacuum & Wipe nozzle and the water
tank is used.
The appliance builds up static electricity.
The lower the air humidity, the more state
electricity is build up.
The dust and dirt that is vacuumed up is
static.
Possible cause
The wetting strip is blocked by dirt.
The microfiber mopping pad is not placed
correctly and blocks the wetting strip as a
result.
The water tank is empty or nearly empty.
A microfiber mopping pad is used that is
not supplied by Philips.
Lime scale has build up in the wetting strip. Buy a new wetting strip in the online Philips shop at
The air channels on the Vacuum & Wipe
nozzle are blocked.
The water tank cap is not attached
properly.
The strip is not placed properly in the
bottom of the water tank.
Too much liquid cleaner has been added to
the water.
The microfiber mopping pad is not placed
correctly.
An incorrect mopping pad is used.
Solution
No action needed. If you prefer to clean with a consistent
power of your choice, disable this smart feature in the
menu of your appliance.
Empty the dust bucket. Clean the filter and the cyclone.
Make sure the filter is cleaned regularly and make sure any
hair and dirt stuck in the cyclone is removed. Follow the
instructions of the user manual.
Clean the brush with a pair of scissors or by hand. See the
instructions in the user manual.
Attach the PrecisionCleaning nozzle to experience the Floor
Type Recognition function.
Discharge the appliance by frequently holding the tube
against other metal objects in the room (for example the
legs of a table or chair, etc.). Or raise the air humidity level
in the room.
Empty the dust container and clean the filter (Fig. 7)
according to the instructions in the user manual.
Solution
Remove the wetting strip (Fig. 9) and clean it. Place the
clean wetting strip back (Fig. 10).
Make sure that you place the mopping pad correctly. Check
the user manual for proper placement.
Refill the water tank.
Only use an original Philips microfiber mopping pad. The
mopping pads can be bought in the online Philips shop at
www.philips.com/support or at your Philips dealer.
www.philips.com/support or at your Philips dealer.
Open the lids of the air channels on both sides of the tube
on the Vacuum and Mop nozzle. Clean the channels (Fig.
11). Close the lids and turn the nozzle upside down. Clean
the air channels from the bottom (Fig. 12).
Check the cap and make sure it is fully and properly closed.
Check the strip and make sure that it is fitted properly in
the bottom plate of the water tank.
Use only a few drops of liquid cleaner or use a cleaner that
foams less.
Make sure that the mopping pad is placed correctly. Check
the user manual for proper placement.
Only use Philips XV1700/01 microfiber mopping pad for
the 8000 series. The mopping pads can be bought in the
online Philips shop at www.philips.com/support or at
your Philips dealer.
11