Electronic Function; Operation - Makita LM003J Instruction Manual

Adjusting the handle height
The handle height can be adjusted in two levels.
1. Hold the lower handle, and then turn the knob 90°
while pulling the knob on the lower handle to release the
locking pin. Perform the same procedure on the other side.
► Fig.29: 1. Lower handle 2. Knob
NOTE: Supporting the handle makes it easier to
release the locking pin when pulling the knob.
2. Adjust the handle height, and then turn the knob on
both sides 90°. Make sure that the knobs are securely fixed.
► Fig.30: 1. Knob
Adjusting the traveling speed
► Fig.31: 1. Speed lever
The traveling speed can be adjusted with the speed
lever. To decrease the speed, pull the lever toward you,
and to increase the speed, turn the lever forward.
Using mulching plug
The mulching plug allows you to return the cut grass
to the ground without gathering the cut grass in the
grass basket. When you operate the machine with the
mulching plug, be sure to remove the grass basket or
discharge chute.
NOTICE:
When using the machine with the
mulching plug, make sure that the total length of
grass after cutting is 30 mm or more, and the cut
length is 15 mm or less.
► Fig.32: (1) 30 mm or more (2) 15 mm or less
Using the discharge chute
The discharge chute allows you to discharge the cut
grass to the ground from the right side of the machine
without gathering the cut grass in the grass basket. When
you operate the machine with the discharge chute, be
sure to remove the grass basket and mulching plug.
Using the rear discharge
Using the rear discharge allows you to discharge the cut
grass to the ground from the rear side of the machine
without gathering the cut grass in the grass basket.
When you operate the machine using the rear dis-
charge, be sure to remove the mulching plug, and grass
basket or discharge chute, and close the rear cover.

Electronic function

The machine is equipped with the electronic functions
for easy operation.
• Soft start at driving
The soft-start function minimizes start-up shock,
and makes the machine start smoothly.
• Electric brake
This machine is equipped with an electric brake.
If the machine consistently fails to quickly stop
the mower blades after releasing the switch lever,
have the machine serviced at Makita Authorized
Service Center.

OPERATION

Mowing
WARNING:
Before mowing, clear away sticks
and stones from mowing area. Furthermore, clear
away any weeds from mowing area in advance.
WARNING:
Always wear the safety goggles or
safety glasses with side shields when operating
the mower.
CAUTION:
If the cut grass or foreign object
blocks up inside of the mower body, be sure to
remove the battery cartridges and wear gloves
before removing the grass or foreign object.
NOTICE:
Use this machine for mowing lawn only.
Do not mow weeds with this machine.
► Fig.33
Firmly hold the handle with both hands when mowing.
The mowing speed guideline is approximately 7 to 14
meters per 10 seconds.
► Fig.34
NOTE: When cutting long lawn or dense lawn, if the
unevenness in the length of lawn or poor finish is
found after mowing, or decrease of the motor speed
is found during mowing, decrease the mowing speed
lower than recommended in this manual, or raise the
mowing height.
The center lines of the front wheels are guidelines to mowing
width. Using the center lines as guidelines, mow in strips. Overlap
by one half to one third the previous strip to mow the lawn evenly.
► Fig.35: 1. Mowing width 2. Overlapping area
3. Center line
Change the mowing direction each time to prevent the
grass grain pattern from forming in just one direction.
► Fig.36
Periodically check the grass basket for mowed grass.
Empty the grass before it becomes full. Before every peri-
odical check, be sure to stop and turn off the machine.
NOTICE:
Using the mower with the grass basket
full prevents smooth blade rotation and places
an extra load on the motor, which may cause
breakdown.
Mowing long lawn
Do not try to cut long lawn all at once. Instead, mow the
lawn in steps. Leave a day or two between mowings
until the lawn becomes evenly short.
► Fig.37
NOTE: Mowing long lawn to short length all at once
may cause the lawn to die. The cut lawn may also
block up inside of the mower body.
NOTE: If the unevenness in the length of lawn or poor
finish is found after mowing, or decrease of the motor
speed is found during mowing, decrease the mowing
speed, or raise the mowing height.
19 ENGLISH