Installation Instructions; Installation - Bosch TR5000 24EB Installation Instructions Manual

Installation instructions

2 Installation instructions
• Install the appliance as shown in the illustrations. Observe the
instructions in the text.
2.1

Installation

Unpacking/Removing the cover (Fig. 1)
• Unpack the appliance and check for transport damage. If any
components are damaged, then do not connect the appliance.
• Check that your appliance contains all components included in the
scope of delivery: appliance, installation set with supplementary
sheets, installation instructions, operating instructions.
• Please dispose of the packaging and the old appliance in an
environmentally-friendly manner.
• When removing the cover from either a Type
appliance, please note the following:
The Type cover is fastened by a central closure behind
the service flap.
The Type cover is attached by two screws located on
the underside of the cover.
Preparations for installation (Fig. 2)
WARNING
Important: Only use the supplied installation set.
The supplied water connection nozzles must be installed!
• Shut off water supply. The electrical connection (connection cable)
must be disconnected from the power supply. Unscrew the fuse
or switch off the circuit breaker.
• Install the water connection nozzles according to the instructions
on the supplementary sheet.
• The electrical connection cable can either be guided in at the top (X)
or bottom (Y).
• The rear panel must lie against the cold water connection nozzle
in the position provided for such (8.).
Wall mounting (Fig. 3)
• The grommet must tightly surround the connection cable. If it is
damaged during mounting, the openings must be provided with
watertight sealing.
• The electrical supply terminal can be fitted at the top (X) or
bottom (Y). The sheath of the connection cable must extend for
at least 40 mm into the appliance.
• The distance to the wall is variable. You can compensate for
any unevenness of the wall's surface. With a distance to the wall of
8–16 mm, insert the spacer and install the extender (3.–5.).
• The appliance must be mounted securely on the wall in vertical
position. If necessary, attach it at the lower adjustable screws (6.).
Water connection (Fig. 4)
• Connect the water supply, then open the cold water supply.
• The appliance must be vented. To do so, open the warm water tap
fully and flush out the appliance thoroughly for 1 minute.
Electrical connection/Mounting (Fig. 5)
Limiting the outlet temperature to 53 °C if unit used for shower
purposes.
10
Risk of electric shock!
How to move the temperature limiting switch,
▶ Disconnect the power supply before opening the appliance.
▶ Remove the cover.
▶ Move the temperature limiting switch to the 53°C position
( Fig. 9).
• Only for appliances with power selector switches:
Set the power using the power selector switch before connecting the
wires to the mains connection terminal: Nominal output power left,
reduced output right (1.) and the set output marked on the ratings
plate.
or Type
• Screw the wires tightly into the mains connection terminal.
• Switch on the safety limiter (3.)
• Install the cover - according to either Type
(4.–7.).
Installation note
• The installation of non plug-in ready appliances must be
undertaken by the respective utility operator or by a qualified
specialist company, who can also assist you when you are
requesting the approval of the utility company for installation
of the appliance.
Startup (Fig. 6)
The device is compliant to IEC 61000-3-12.
First start-up
• Switch on the fuses.
• Setting the temperature.
• Initial rinsing: Open the warm water tap fully and allow water to flow
for at least 1 minute. Only then (for safety reasons) will the appliance
begin to heat.
Tip: Should the appliance not start because of a reduced flow-rate,
remove the perlator, shower head or similar from the water tap before
start and repeat the process.
Risk of freezing!
▶ If the appliance is left without power during a long period of no use
and if there is a risk of freezing temperatures in the room, the water
must be drained from the unit ensuring that residual water is
minimum to avoid freezing damages in the heating block. This type of
damages are excluded by warranty.
• Explain the operation of the appliance to the user.
Additional information (Fig. 7)
• If the appliance does not have sufficient water flow due to low water
line pressure in your domestic plumbing system, remove the flow-
rate limiter (1.–3.) or increase supply pressure to the system.
• The integrated flow restriction in the unit ensures a certain
temperature increase in order to grant comfort, so removing this and
in case the water pressure varies it can cause temperature
fluctuations.
• The inlet filter must not be removed. It must always remain in the
appliance even if flow restrictor is removed.
• Priority circuit for the combination with electrical storage heaters:
For operation with a priority circuit, a special load shedding relay
BZ 45L21 (special accessory) is required. Other existing load
shedding relays, with the exception of electronic load shedding
relays, may malfunction (Wiring diagram).
WARNING
WARNING
Tronic 4000 | 5000 | 6000 | 7000 – 6720876037 (2021/12)
or instructions