Trouble Shooting; Rectifying Faults Yourself; Maximum Operating Time - Siemens HB378G2 0Y Series Instruction Manual

Table of Contents

Advertisement

Trouble shooting

en
Press the front panel at the bottom until it clicks
5.
audibly into place (figure
Open the appliance door again slightly and remove
6.
the tea towel.
Screw both screws back in on the left and right.
7.
Put the cover back in place and press on it until it
8.
clicks audibly into place (figure
Close the appliance door.
9.
Caution!
Do not use the cooking compartment again until the
panels have been correctly fitted.
3Trouble shooting
I f a fault occurs, there is often a simple explanation.
T r o u b l e s h o o t i n g
Before calling the after-sales service, please refer to the
fault table and attempt to correct the fault yourself.

Rectifying faults yourself

You can often easily rectify technical faults with the
appliance yourself.
If a dish does not turn out exactly as you wanted, you
can find useful cooking tips and instructions at the end
of this instruction manual. ~ "Tested for you in our
cooking studio" on page 29
Fault
Possible
cause
The appliance is
Defective cir-
not working.
cuit breaker.
Power failure Check whether the kitchen light
The time is flash-
Power failure. Reset the time.
ing on the display.
The settings on
The child-
the appliance
proof lock is
cannot be config-
activated.
ured. A key sym-
bol has lit up on
the display or
†'""
.
24
).
%
).
&
Notes/remedy
Check the circuit breaker in the
fuse box.
or other kitchen appliances are
working.
Deactivate the childproof lock by
pressing and holding the button
with the key symbol for approx. 4
seconds.
The appliance
The appliance
door will not
door is locked
open. A key sym-
with the child-
bol has lit up on
proof lock.
the display.
The appliance
The appliance
door will not
door is locked
open. A lock
by the clean-
ing function.
symbol
H
has lit
up on the display.
After an operating
The appliance
mode is switched
has not
cooled down
on,
œ
is flashing
sufficiently.
on the display.
The appliance is
Demo mode
not heating. The
is activated.
colon is flashing
on the display. On
some appliances,
a
š
will also
appear on the dis-
play.
--------
:
Warning – Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be
carried out and damaged power cables replaced by
one of our trained after-sales technicians. If the
appliance is defective, unplug the appliance from the
mains or switch off the circuit breaker in the fuse box.
Contact the after-sales service.
Error messages on the display
If an error message with "
e.g.
-
, touch the
"ܠ
„ƒ
error message. Reset the time, if necessary.
If the fault was a one-off, you can continue to use your
appliance as normal. If the error message appears
again, call our after-sales service and quote the exact
error message and the E no. of your appliance.
~ "Customer service" on page 25

Maximum operating time

If you do not change the settings on your appliance for
several hours, the appliance will stop heating
automatically. This prevents unintentional continuous
operation.
When the maximum operating time is reached depends
on the various different settings that have been
configured on the appliance.
Maximum operating time reached
appears on the display.
"‰
Turn the function selector to the "Off" position. You can
configure new settings if required.
To prevent the appliance from switching off when
Tip:
you do not want it to, e.g. with an extremely long
cooking time, you should always set a cooking time.
The appliance will heat up until the set cooking time has
elapsed.
Deactivate the childproof lock by
pressing and holding the button
with the key symbol for approx. 4
seconds.
The lock can be switched off in
the basic settings.
Wait until the cooking compart-
ment has cooled down and the
lock symbol
H
has gone out.
Switch off the appliance, allow it
to cool down and switch on the
operating mode again.
Briefly disconnect the appliance
from the mains (switch off the cir-
cuit breaker in the fuse box) and
then deactivate demo mode
within approx. 5 minutes by
changing the basic setting
or
™›
to
. ~ "Basic settings"
on page 16
" appears on the display,
"
button. This will reset the
v
™‚„

Advertisement

Table of Contents
loading

Table of Contents