Lutron Electronics Caseta Diva Smart Dimmer Quick Start Manual

Pre-Installation

quick-start guide
Diva Smart Dimmer and
Pico Paddle Remote
0302106 Rev. A
Welcome— and thank you for purchasing a Diva smart dimmer
and Pico paddle remote kit.
Wiring Wizard
Find the right LED
Double your warranty
Love Caséta Wireless controls? Have ideas for making them
better? Tell us what you think and we'll extend your warranty
by 1 year. www.casetawireless.com/register
Contents supplied
(DVRF-PKG1D)
Dimmer Pico paddle remote Wallbox adapter
(DVRF-6L) (PJ2-P2B) (PICO-WBX-ADAPT)
Claro wallplate (A) Large wire (B) Small wire

Installing your Pico paddle remote (secondary location)

(CW-1)
connectors (x6) connector (x1)

A. Over Wallbox Installation

1
Ensure power is still OFF
(C) Silver 6-32 x 7/8 in (D) Black 6-20 x 1.25 in
machine screws (x4) wood screws (x2)
Jumper
(E) Wall anchors (x2)
wire
WARNING! Shock Hazard.
May result in serious injury or death. Turn off the
WARNING! Shock Hazard. May result in serious injury or death.
power before installing. NOTE: If the wallbox
Turn off power before installing. NOTE: If cover plate is removed,
only install over wall surface. DO NOT install over wallbox. adapter cover plate is removed, only install over
wall surface. DO NOT install over wallbox.
Tools you'll need
Flat-head screwdriver Pliers
6
Slide Pico paddle remote onto wallbox adapter
Phillips-head screwdriver Drill and drill bit
3/16 in (5 mm)
b a
1.
Works with energy efficient dimmable
light bulbs:
LED—up to 150 W Incandescent—up to
600 W

B. Wall Surface Installation

Halogen—up to 600 W
1
Remove cover plate
NOTE: You can mix and match dimmable LED and CFLs,
as well as halogen and incandescent light bulbs with Caséta
Pry
dimmers.
Dimmable LED and CFL light bulbs vary in their dimming
performance. If you're using these bulbs and they flicker or
unexpectedly turn off, please see the "Adjusting low-end trim"
section on page 2 for information on adjusting the dimmer for
best bulb performance.

Ganging and Derating

Double Gang Triple Gang
5
1.
Attach wallplate
1.
Important note:
Multi-gang installations may reduce the dimmer's maximum wattage
rating. See the chart below for maximum wattage information.
Maximum* wattage derating chart (120 V~ 50/60 Hz)
Load Type Single gang Double gang Triple gang
LED & CFL 150 W 150 W 150 W
or *
Adapter Plate
Incandescent & Halogen 600 W 500 W 400 W
* For maximum wattage information when mixing light bulb types
see www.casetawireless.com/ganging

Installing your in-wall dimmer (main location)

Identify installation type
Option 1: Wireless 3-Way / Single-Pole + WARNING: SHOCK HAZARD.
Pico Paddle Remote May result in serious injury or death.
Turn off power at circuit breaker or
fuse before installing.
Important wiring note:
Option 2: Wireless 3-Way / Replace Mechanical Some lights have one wall switch— called single-pole, while others have two wall
3-way Switch with the Pico Paddle Remote switches— called 3-way (such as stair lights, which have a switch at both the top and
bottom of the stairs). Be sure to pay close attention to the appropriate wiring diagrams in
the following steps.
To access more detailed information and step-by-step instructions for specific wiring
scenarios please use the "Wiring Wizard" QR code to the left.
Option 3: Wireless Multi-Location /
Retain Mechanical 3-Way Switch +
Pico Paddle Remote
Option 3: Wireless multi-location / retain mechanical 3-way switch + Pico paddle remote
For lights switched from two
Follow the "Wiring Wizard" QR code for detailed instructions.
Option 4: Wired Multi-Location [3-Way / 4-Way with
Accessory Switch(es)] + Pico Paddle Remote
replacing existing switch (3-way applications) with Pico paddle remotes
2
Unscrew existing switch from wall
1.
Remove the wallplate. Remove the screws securing the switch and pull it away
from the wall (do not disconnect wires).
2.
2
Mark wall and drill holes
Cover Plate
2. If wallplate removal is necessary, pull forcefully.
'snap'
Wallplate
Option 1: Wireless 3-way /single pole +
Disconnect power
Pico paddle remote
For lights switched from
wired location:
NOTE: Red and black wires on dimmer
are interchangeable.
(A)
Red
Use blue
connector
Blue
WARNING! Shock Hazard. May result in serious injury or death.
Turn off power before installing. NOTE: If cover plate is removed,
(A)
only install over wall surface. DO NOT install over wallbox.
Black
(A)
Green wire
1.
2.
wired locations with a wireless control from one or more remote locations:
3
Disconnect wires
2.
Place tag to identify wire on
different color screw
Ground
Different color screw
(Green / Bare
Copper)
7
Attach wallplate
1.
Adapter
Plate
OR
3
3/16 in
(5 mm)
6
Side View
Pico
paddle
remote
Option 2: Wireless 3-way / replace mechanical 3-way switch with the Pico paddle remote
1.
one
For lights switched from one wired location and one wireless
IMPORTANT: Before disconnecting the existing devices, tag the wire connected to the different colored screw
(typically a black wire, but wire colors vary, and labeled COM). This is the Common wire.
Use blue
Tagged Wire
connector (B)
(A)
(B)
Blue
Red
(A)
Neutral connection
Black
(A) NOTE:
Insert
be tied to load side. If the
and
twist to switch does not work once
tighten you're all done, turn off power
and flip the red and black wires.
Ground
Ground
(Green / Bare
(Green / Bare Copper)
Green wire
Copper)
Option 4: 3-way/4-way with Claro smart accessory switch(es) + Pico paddle remote
For lights switched from two or more wired locations with a wireless control from one or more remote locations:
See Claro Smart Accessory Switch Installation Guide (model DVRF-AS) for details on installing accessory
switches. See section A, "Over Wallbox Installation" for replacing any switch location with a Pico paddle remote.
See section B, "Wall Surface Installation" for adding additional points of control using the Pico paddle remote.
4
Connect the wires
Using the provided wire connectors, connect the wires together
(EXCEPT for the ground wire and the neutral wires). Cap the ground wire
and cap the neutral wires.
(A)
Neutral connection
Neutral connection
(A)
Ground (Green/Bare Copper)
If wallplate removal is necessary,
2.
pull forcefully.
'snap'
Wallplate
Mount the wallbox adapter
1
2
b
a
(D)
(E)
Check mounting
Correct Incorrect
Pico
paddle
remote
Verify that Step 1

was completed
Wallplate
2.
location:
Red dimmer wire must
5
Mount the wallbox adapter
(C)
8
Restore power
4
Slide Pico paddle remote onto wallbox adapter
7
Restore power