Page 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.
ID label (see below). This information is required for us to provide proper tech support, and it helps us determine if updated documentation is available for your machine. Manufacture Date Serial Number Model G8027 (Mfd. Since 09/23)
If normal safety pre- respect. Failure to do so could result in cautions are overlooked or ignored, seri- serious personal injury, damage to equip- ous personal injury may occur. ment, or poor work results. Model G8027 (Mfd. Since 09/23)
ON/OFF and prevents accidental start- up. Removal of yellow key disables switch, E. Collection Bag: Collects 2.3 cubic feet of preventing motor from starting. wood dust and has a quick-disconnect bag clamp for disposal. Model G8027 (Mfd. Since 09/23)
MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G8027 1 HP DUST COLLECTOR Product Dimensions: Weight................................51 lbs. Width (side-to-side) x Depth (front-to-back) x Height..............25-1/2 x 15 x 63 in.
Page 8
The information contained herein is deemed accurate as of 7/20/2023 and represents our most recent product specifications. Model G8027 PAGE 2 OF 2 Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. Model G8027 (Mfd. Since 09/23)
Never operate under the influence of drugs or injury or blindness from flying particles. Everyday alcohol, when tired, or when distracted. eyeglasses are NOT approved safety glasses. Model G8027 (Mfd. Since 09/23)
Page 10
Make sure they are properly installed, you experience difficulties performing the intend- undamaged, and working correctly BEFORE ed operation, stop using the machine! Contact our operating machine. Technical Support at (570) 546-9663. Model G8027 (Mfd. Since 09/23)
DO NOT place dust collector where it can what type of wood dust you will be exposed to in be exposed to rain or moisture, which creates a case of an allergic reaction. shock hazard and will reduce life of machine. Model G8027 (Mfd. Since 09/23)
Page 13
Two-prong outlets do not meet the grounding requirements for this machine. Do not modify or use an adapter on the plug provided—if it will not fit the outlet, have a qualified electrician install the proper outlet with a verified ground. -11- Model G8027 (Mfd. Since 09/23)
IMPORTANT: Save all packaging materials until you are completely satisfied with the machine and have resolved any issues between Grizzly or the shipping agent. You MUST have the original pack- aging to file a freight claim. It is also extremely helpful if you need to return your machine later.
— Flat Washers 5mm ........ 22 —Phillips Head Screws M5-.8 x 15 .... 6 —Phillips Head Screws M5-.8 x 10 ..16 —Phillips Head Screws M4-.7 x 8 ....2 —Hex Wrenches 4, 5mm .....1 Ea. -13- Model G8027 (Mfd. Since 09/23)
Hardware Recognition Chart USE THIS CHART TO MATCH UP HARDWARE DURING THE INVENTORY AND ASSEMBLY PROCESS. Flat Head Screw -14- Model G8027 (Mfd. Since 09/23)
Only install in an Shadows, glare, or strobe effects that may distract access restricted location. or impede the operator must be eliminated. 25½" Electrical Connection 15" Figure 5. Minimum working clearances. -15- Model G8027 (Mfd. Since 09/23)
15 hex bolts and 8mm flat washers (see Figure 7). Rubber Gasket Column & Motor Plate Assembly Figure 9. Attaching collector to motor/impeller housing (rubber gasket hidden by motor/impeller housing). Figure 7. Attaching column and motor plate assembly. -16- Model G8027 (Mfd. Since 09/23)
Page 19
5mm flat washers (see Figure 11). 10. Without moving bolts, tighten (2) hex nuts shown in Figure 13 to secure bolts. Figure 11. Attaching collection bag support rods Impeller to base plate. Figure 13. Location of motor plate bolts. -17- Model G8027 (Mfd. Since 09/23)
Page 20
Figure 15, then hook spring bar to cleats on other end of belt and tighten latch to secure. Figure 16. Filter bag installed. Latch Spring Bar Belt Figure 15. Bag clamp components. -18- Model G8027 (Mfd. Since 09/23)
Figure 17. Ground jumper wire when using However, the cost of specifically designed flexible plastic blast gates or elbows and metal duct. duct can vary greatly. Grizzly offers polyethylene and steel flex hose. We also recommend wrapping the outside of all...
Page 22
Figure 20. Dust port size and quantity per 4" average machine. 5" 6" To solve any other dust collection questions, Grizzly offers a guide book entitled Dust Collection 7" 1200 Basics that will help you design your system. 8" 1600 9"...
This safety feature must at full amperage load, which could trip your work properly before proceeding with reg- circuit breaker or blow fuse. ular operations. Call Tech Support for help. Connect machine to power. -21- Model G8027 (Mfd. Since 09/23)
45° elbows in place of 90° elbows when- formal training before beginning any proj- ever possible). ects. Regardless of the content in this sec- tion, Grizzly Industrial will not be held liable for accidents caused by lack of training. -22- Model G8027 (Mfd. Since 09/23)
G5051—30 Micron Fabric Collection Bag To reduce this risk, only install accessories T24268—Plastic Collection Bag recommended for this machine by Grizzly. To ensure consistent results, buy Grizzly replace- ment dust collector bags. Keep several spares on hand. NOTICE Refer to our website or latest catalog for additional recommended accessories.
Place the cord away from potential damage sources, such Re-install bag or replace it with a new one. as high traffic areas, sharp objects, heat sources, harsh chemicals, water, damp areas, etc. -24- Model G8027 (Mfd. Since 09/23)
2. Fix/replace fan cover; replace loose/damaged fan. 3. Centrifugal switch needs adjustment/at fault. 3. Adjust/replace if at fault. 4. Motor bearings at fault. 4. Test by rotating shaft; rotational grinding/loose shaft requires bearing replacement. -25- Model G8027 (Mfd. Since 09/23)
Page 28
8. Upgrade to larger dust collector. Dust collector 1. Duct clamp(s) or bag(s) not properly clamped 1. Secure ducts and bags, making sure duct/bag blows sawdust and secured; ducting loose/damaged. clamp(s) are tight; tighten/replace ducting. into the air. -26- Model G8027 (Mfd. Since 09/23)
Install inlet cover with screws removed in DISCONNECT MACHINE FROM POWER! Step 2. Remove (12) Phillips head screws shown in Figure 27 to remove inlet cover. Inlet Cover x 12 Figure 27. Location of inlet cover and securing screws. -27- Model G8027 (Mfd. Since 09/23)
Technical Support at (570) 546-9663. The photos and diagrams included in this section are best viewed in color. You can view these pages in color at www.grizzly.com. -28- Model G8027 (Mfd. Since 09/23)
SECTION 9: PARTS We do our best to stock replacement parts when possible, but we cannot guarantee that all parts shown are available for purchase. Call (800) 523-4777 or visit www.grizzly.com/parts to check for availability. Main 18-1 18-4 18-2 18-5...
Page 33
S CAPACITOR 200M 125V 1-1/2 X 2-3/4 P8027042 RUBBER GASKET 18-7 P8027018-7 OL SWITCH YINXIANG 9A 125/250V 50VDC P8027049 STRAIN RELIEF TYPE-1 5/8 P8027019 RUBBER GASKET BUY PARTS ONLINE AT GRIZZLY.COM! -31- Model G8027 (Mfd. Since 09/23) Scan QR code to visit our Parts Store.
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com. BUY PARTS ONLINE AT GRIZZLY.COM! -32- Model G8027 (Mfd.
WARRANTY & RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.