Subscribe to Our Youtube Channel
Related Manuals for Anderson ANM76
Summary of Contents for Anderson ANM76
- Page 1 Anderson Thermal Solutions (Suzhou) Co., LTD ANM76 Burner Operation Manual No： ATS–Operation Manual–ANM76 Subject:： ANM76 Burner Operation Manual Version ： V1.0 Author ： Wilson Sun Review ： David...
-
Page 2: Table Of Contents
Disclaimer Notice ............1 Liability And Warranty ............1 Safety Guide ............. 1 Fuel Information ............2 ANM76 Series Burner Description..........2 Burner Component Introduction ....Error! Bookmark not defined. Burner Operation Data ............. 4 Performance Graphs ............5 Burner datasheet ............5 Burner Installation To Be Noted .......... -
Page 3: Disclaimer Notice
Loss of or damage to the use of materials that sell, install, use, fail to use or repair or replace Anderson related products. -
Page 4: Fuel Information
1,013.25 mbar, 0°C 5. ANM76 Series Burner Description ANM76 series burner is a patented product of Anderson Thermal Solutions (Suzhou) Co., Ltd. This series of linear burners adopts a modular structure design concept and can be configured to match shapes according to site requirements. It is an ideal choice for generating large amount of clean and hot air. -
Page 5: Burner Component Introduction
850°C 6. Burner Component Introduction ANM76 series burners are mainly made up of burner body, fire plate as flame shield, diffuser plate. Different parts were connected by rivets, screws and bolts. Shown as below Fig 1 is the diagram of the burner, in which the air wing and outer connectors are made of stainless steel, gas channels and connectors are also stainless steel. -
Page 6: Burner Operation Data
Anderson Thermal Solutions – ANM76 Burner Operation Manual Fig 1. ANM76 Series Burner Explosion View 7. Burner Operation Data – Maximum input: 1000 kW/m（when air differential pressure across burner is 2.5mbar） – Minimum input: 100 kW/m – Fuel inlet pressure: 3-85 mbar。... -
Page 7: Performance Graphs
Operation Curve Curve 9. Burner datasheet The input and flame length curves of the ANM76 series burners are shown in Fig 4 and Fig Fig 4. ANM76 Series Burner Input Curve Fig 5. ANM76 Series Burner Flame Length Anderson Thermal Soluions（Suzhou）Co., Ltd... -
Page 8: Burner Installation To Be Noted
11. Burner start Special attention: The ANM76 Series burners, described herein, are designed to mix fuel with ai. All fuel burning devices are capable of producing fires and explosions, if improperly applied, installed, adjusted, controlled, or maintained. Do not bypass any safety logics; Never try to light a burner if it shows signs of damage or malfunction. -
Page 9: Burner Get To Operation Mode
Anderson Thermal Solutions – ANM76 Burner Operation Manual difference before and after the burner profile plate. Start the combustion air fan, adjust it to 100% of the flow rate, measure the pressure difference between the combustion air and the downstream of the burner, the design DP is 2-2.5 mbar. -
Page 10: Stop Procedure
Leak detect, control functions of the equipment must be included in the scope of audit. Only Anderson technicians or those who are trained and qualified by Anderson, as well as other relevant professionals, can maintain the burners. -
Page 11: Yearly Checklist
Anderson Thermal Solutions – ANM76 Burner Operation Manual 12.2 Yearly checklist – Leak test the safety shut-off valves and gas train for tightness of closure to make sure no leakage. – Test the pressure switch settings by checking the switch movements against pressure settings and comparing these with the actual pressure. -
Page 12: Appendix
Anderson Thermal Solutions – ANM76 Burner Operation Manual 14. Appendix 14.1Training Record Each trained person must verify that he has read and understood the contents of the operating manual and know how to operate and maintain this series of burners correctly. -
Page 13: Annual Audit Record
Anderson Thermal Solutions – ANM76 Burner Operation Manual 14.3 Annual Audit Record Yearly audit list as follow but not only included Function Audit Date Inspector Problem description Next Audit Time Leak test Pressure switch test Cable and connectors Burner bodies and air wings Attention：...
Need help?
Do you have a question about the ANM76 and is the answer not in the manual?
Questions and answers