Table of Contents
Advertisement
8 8
f
f '
' \ \
WIPER BLADE
WIPER BLADE
Fig. l-wiper Arm and Blade (Disassembled)
Fig. l-wiper Arm and Blade (Disassembled)
(3) Holding the blade assembly at the center, de-
(3) Holding the blade assembly at the center, de-
press one of the small plastic knobs (Fig. 1).
press one of the small plastic knobs (Fig. 1).
(4) With knob depressed, slide the bracket off of
(4) With knob depressed, slide the bracket off of
the tension arm and rubber filler.
the tension arm and rubber filler.
(5) Withdraw wiper filler from remaining bracket
(5) Withdraw wiper filler from remaining bracket
and tension arm assembly. Discard old rubber filler.
and tension arm assembly. Discard old rubber filler.
installation
installation
(1) Insert the new filler into the clamps of the
(1) Insert the new filler into the clamps of the
bracket and tension arm assembly.
bracket and tension arm assembly.
(2) Slide the mating bracket over the end of the rub-
(2) Slide the mating bracket over the end of the rub-
ber
ber
filler.
filler.
(3) With the plastic knob depressed, engage the
(3) With the plastic knob depressed, engage the
end of the tension arm into the slots of the bracket and
end of the tension arm into the slots of the bracket and
release the knob.
release the knob.
(4) Elevate the end of the wiper arm from the wind-
(4) Elevate the end of the wiper arm from the wind-
shield and holding the lock lever depressed, engage
shield and holding the lock lever depressed, engage
the wiper blade slot over the pivot pin of the wiper
the wiper blade slot over the pivot pin of the wiper
arm.
arm.
(5) Release the lock lever and lower blade and arm
(5) Release the lock lever and lower blade and arm
assembly to the windshield.
assembly to the windshield.
2. W
2. WIPER
IPER A A RM ADJ
RM ADJ US
(1) Operate wiper and observe travel and parking
(1) Operate wiper and observe travel and parking
position of wiper blade.
position of wiper blade.
(2) Loosen wiper arms at pivots.
(2) Loosen wiper arms at pivots.
(3) Operate motor several times and turn off wiper
(3) Operate motor several times and turn off wiper
WIPER ARM
WIPER ARM
/
. .
/
.k .k
K N O B
K N O B
UST T MENT
MENT
AC C C ES
AC
ESS S O O R R IES
IES
switch (Do not use ignition switch), this permits motor
switch (Do not use ignition switch), this permits motor
to stop at normal parking position.
to stop at normal parking position.
(4) Position wiper blades at the lower windshield
(4) Position wiper blades at the lower windshield
moulding and tighten pivot nuts. (Variable speed
moulding and tighten pivot nuts. (Variable speed
motors only).
motors only).
j j
(5 (5
For single speed motors position wiper blades
For single speed motors position wiper blades
12 12
one inch above moulding and tighten pivot nuts.
one inch above moulding and tighten pivot nuts.
(6) Operate wipers and observe travel of both
(6) Operate wipers and observe travel of both
blades.
blades.
(7) Wet windshield and again operate blades and
(7) Wet windshield and again operate blades and
observe wiping pattern.
observe wiping pattern.
61 xl 42
61 xl 42
3. RADIO
3. RADIO C C O O NDENS
With the use of thermal instrument gauges, a new
With the use of thermal instrument gauges, a new
voltage limiter is mounted on the rear of the instrument
voltage limiter is mounted on the rear of the instrument
cluster. The voltage limiter reduces battery voltage to
cluster. The voltage limiter reduces battery voltage to
approximately 5.0 volts by the means of vibrator points.
approximately 5.0 volts by the means of vibrator points.
The
The high
high sens
sensiti itivit
vity y of of the
ing of these points and the addition, of a condenser
ing of these points and the
will absorb this arcing or static.
will absorb this arcing or static.
Th e e mo
Th
mo un
un ti ti ng ng br br ac ac ke ke t t of of th th e e co co nd
and may be inserted under the head of the attaching
and may be inserted under the head of the attaching
screw (Fig. 2) without removing the voltage limiter.
screw (Fig. 2) without removing the voltage limiter.
The wire
The
wire lead
lead of of the
vided output post of the limiter.
vided output post of the limiter.
Figures 3 and 4 shows the schematic wiring dia-
Figures 3 and 4 shows the schematic wiring dia-
grams for the two model radios.
grams for the two model radios.
F F ig. 2-Radio C
ig. 2-Radio C onde
NDENSER
ER INST
INST A A L L L L A A T T IO
the radi
radio o may
may pic
pick k up
addition, of a condenser
nd en en se se r r is is sl sl ot ot te te d d
the condens
condenser er is is attac
attached
hed to to the
VO L T AG E L I M I T ER
VO L T AG E L I M I T ER
ON REAR OF
ON REAR OF
NT
NT
CONbENSER
CONbENSER
onde nser
nser Inst
Installa
alla tion
tion
ION N
up the
the arc-
arc-
the pr pro- o-
C C
U S T E R )
U S T E R )
L L
6 1 X 3 2 8
6 1 X 3 2 8
a a
Advertisement
Table of Contents
