Table of Contents
Advertisement
shield to disengage the retaining spring clips from the
shield to disengage the retaining spring clips from the
speedometer and instrument panel base.
speedometer and instrument panel base.
(3) Disconnect the high beam indicator light wire,
(3) Disconnect the high beam indicator light wire,
the ammeter gauge wires and lamp bulb and the oil
the ammeter gauge wires and lamp bulb and the oil
pressure warning light socket and bulb.
pressure warning light socket and bulb.
(4) Remove the four screws attaching the speed-
(4) Remove the four screws attaching the speed-
ometer and instrument cluster and bezel to the speed-
ometer and instrument cluster and bezel to the speed-
ometer and instrument panel base. Two screws are lo-
ometer and instrument panel base. Two screws are lo-
cated at rear of instrument cIusters
cated at rear of instrument cIusters (one each
the other two screws attach the cluster bezel to the
the other two screws attach the cluster bezel to the
base at front of bezel. Remove clusters and bezel as an
base at front of bezel. Remove clusters and bezel as an
assembly.
assembly.
(5) Disconnect the speedometer cable and speed-
(5) Disconnect the speedometer cable and speed-
ometer lamp connectors at speedometer head.
ometer lamp connectors at speedometer head.
(6) Remove the four screws attaching the speed-
(6) Remove the four screws attaching the speed-
ometer to the speedometer and instrument panel base
ometer to the speedometer and instrument panel base
and remove the speedometer assembly.
and remove the speedometer assembly.
lnstallcJtion
lnstallcJtion
( 1) Position the speedometer on the instrument pan-
( 1) Position the speedometer on the instrument pan-
el base and install the four attaching screws.
el base and install the four attaching screws.
(2) Connect speedometer cable and speedometer
(2) Connect speedometer cable and speedometer
lamps at speedometer head.
lamps at speedometer head.
(3) Position the speedometer and instrument
(3) Position the speedometer and instrument clus-
ters and bezel in the instrument panel base and install
ters and bezel in the instrument panel base and install
the four attaching screws.
the four attaching screws.
(4) Connect the ammeter wires and lamps.
(4) Connect the ammeter wires and lamps.
(5) Position the speedometer and instrument panel
(5) Position the speedometer and instrument panel
cover on panel base, engaging the retaining spring
cover on panel base, engaging the retaining spring
clips in the slots of the speedometer and instrument
clips in the slots of the speedometer and instrument
panel base. Carefully align the cover at the joint of
panel base. Carefully align the cover at the joint of
the base and cover and install the attaching screws.
the base and cover and install the attaching screws.
Install the two screws attaching cover to instrument
Install the two screws attaching cover to instrument
bezel.
bezel.
(6) Connect the battery cable to battery negative
(6) Connect the battery cable to battery negative
terminal.
terminal.
2. AMM
2. AMMET
ETER
W A R N I N G L I G H T
W A R N I N G L I G H T
Removal
Removal
Perform operations 1 through 4 under "Speedometer
Perform operations 1 through 4 under "Speedometer
Removal" and proceed as follows:
Removal" and proceed as follows:
(1) Remove the three screws at rear of cluster and
(1) Remove the three screws at rear of cluster and
remove the ammeter and ammeter lamp and/or oil
remove the ammeter and ammeter lamp and/or oil
pressure warning light assembly.
pressure warning light assembly.
! !
NOTE: Fuel gauge, temperature gauge and
NOTE: Fuel gauge, temperature gauge and
clock can be removed on bench by removing
clock
can be removed on bench by removing
the sc
scr r ews
ews attaching the gauges to the
the
ter. To
ter. To remove
remove the
with a suitable tool and remove
with a suitable tool and
knob. Do not remove clock stem. Clock is
knob. Do not remove
tained to the cluster by studs. nuts and wash-
tained to the cluster by studs. nuts and wash-
ers.
ers.
(4) If necessary to replace the cluster bezel glass,
(4) If necessary to replace the cluster bezel glass,
ER
AND/OR OIL PRESSURE
AND/OR OIL PRESSURE
attaching the gauges to the clus-
the clock,
clock, hold the clock stem
hold the clock stem
remove the clock
clock stem. Clock is re-
(2) Working under the instrument panel, remove
(2) Working under the instrument panel, remove
the wires from the terminals on the temperature gauge.
the wires from the terminals on the temperature gauge.
(3) Remove the gauge light bulb.
(3) Remove the gauge light bulb.
(4) Remove the two screws attaching the tempera-
(4) Remove the two screws attaching the tempera-
ture gauge to the instrument cluster housing and care-
ture gauge to the instrument cluster housing and care-
fully withdraw the temperature gauge from the cluster
fully withdraw the temperature gauge from the cluster
housing.
housing.
Installation
Installation
(one each side)
side)
( 1) Carefully position the temperature gauge in the
( 1) Carefully position the temperature gauge in the
instrument cluster housing and install the two (2) re-
instrument cluster housing and install the two (2) re-
taining
taining
(2) Install the light bulb in the gauge housing and
(2) Install the light bulb in the gauge housing and
connect the wires to the gauge terminals.
connect the wires to the gauge terminals.
(3) Connect the battery ground strap.
(3) Connect the battery ground strap.
4. FUEL GAUGE
4. FUEL GAUGE
Removal
Removal
(1) Disconnect the cable at battery negative ter-
(1) Disconnect the cable at battery negative ter-
minal.
minal.
(2) Remove the wires from the terminals on the fuel
(2) Remove the wires from the terminals on the fuel
gauge.
gauge.
(3) Remove the gauge light bulb.
(3) Remove the gauge light bulb.
(4) Remove the two screws attaching the fuel gauge
(4) Remove the two screws attaching the fuel gauge
clus-
constant voltage regulator to the instrument cluster
constant voltage regulator to the instrument cluster
housing and carefully pull fuel gauge out of the clus-
housing and carefully pull fuel gauge out of the clus-
ter housing.
ter housing.
Installation
Installation
(1) Carefully position the fuel gauge in the instru-
(1) Carefully position the fuel gauge in the instru-
ment cluster housing and install the two (2) retaining
ment cluster housing and install the two (2) retaining
screws.
screws.
(2) Install the light bulb in the gauge housing and
(2) Install the light bulb in the gauge housing and
connect the wires to the gauge terminals.
connect the wires to the gauge terminals.
(3) Connect the cable to battery negative terminal.
(3) Connect the cable to battery negative terminal.
5. INSTRUMENT CLUSTER ASSEMBLY
5. INSTRUMENT CLUSTER ASSEMBLY
AND/OR CLUSTER BEZEL GLASS
AND/OR CLUSTER BEZEL GLASS
Removal
Removal
j j
(1 (1
(2) Working from below the instrument panel re-
(2) Working from below the instrument panel re-
move the four nuts and lockwashers attaching the in-
move the four nuts and lockwashers attaching the in-
strument cluster to the instrument panel and disconnect
strument cluster to the instrument panel and disconnect
all wires and connectors.
all wires and connectors.
(3) Carefully pull the cluster assembly from front
(3) Carefully pull the cluster assembly from front
of instrument panel.
of instrument panel.
EL
EL EC
ECT T RIC
RICA A L- L-IN
INST
ST RU
RU MENT
MENT S S
remove clock stem knob,
remove clock stem knob,
remove the two screws attaching the cluster bezel to
remove the two screws attaching the cluster bezel to
clus-
instrument cluster.
instrument cluster.
Installation
Installation
the clock
( 1) Position instrument cluster panel in the
( 1) Position instrument cluster panel in the instru-
re-
ment panel and install the attaching washers and nuts.
ment panel and install the attaching washers and nuts.
(2) Connect all wires disconnected at time of re re - -
(2) Connect all wires disconnected at time of
moval.
moval.
(3) Connect cable at battery negative terminal.
(3) Connect cable at battery negative terminal.
screws.
screws.
Disconnect cable at battery negative terminal.
Disconnect cable at battery negative terminal.
(do not
(do not
57
57
remove stem) and
remove stem) and
instru-
Advertisement
Table of Contents
