Kenwood TS-950SDX Instruction Manual page 32

4-3-4. AM Mode
Place the POWER switch ON.
. Place the AM key.
. Enter the desired frequency.
. Set the METER switch to ALC.
. Press the microphone PTT switch, or set the REC/
SEND switch to SEND. The ON AIR indicator will
light.
6. Adjust the CAR LEVEL control so that the meter
indicates 40 watts.
theo
s . 20 40 ome
Lilie eevee en teleacely of
so o 108 180 308 Bee
Akon
a
PowER
awa cononcocoonaonanaoooosceoongos
renee 3 SS
aposaeadsSoaeacedaeccsconpesne
7. Speak into the microphone and adjust the MIC
gain control so that the meter indicates 80 watts.
a.
a oe ee ee 20 an _ mon
Sadnndend 0009) s0000009000000
POWER
8. Release the PTT switch, or place the REC/SEND
switch to REC. The ON AIR indicator will turn
OFF.
4-3-5. FSK Mode
. Connect the RTTY keyboard to the FSK key jack
on the rear panel.
2. Place the POWER switch ON.
3. Place the FM key.
4. Select the desired FSK shift. (See section 4-2-13.}
5.
6
7
=
. Enter the desired frequency.
. Set the METER switch to ALC.
. Set the REC/SEND switch to SEND. The ON AIR
indicator will light.
8. Adjust the PROCESSOR-OUT control so that the
meter deflection is within the ALC zone.
9. Operate the RTTY keyboard.
10, Place the REC/SEND switch to REC. The ON AIR
indicator will turn OFF.
11. Follow the instructions contained in RTTY
keyboard operating manual for the correct
settings before you start transmitting. The
DATA mode will be automatically selected in
the FSK mode. The shift range can be selected
in the POWER ON function selection. (Please
refer to Section 4-2-13.)
4-3-6. CW Mode
@Sidetone oscillator
The transceiver contains a sidetone oscillator circuit
to permit you to monitor your own signal. If the
key is closed in CW with the VOX/MAN switch set
to MAN, transmit will not be selected, but a
sidetone will be heard from the speaker to allow
Morse code training. The volume of the sidetone
can be adjusted internally (Please refer to Section 5-
6-3).
32
o
Connect a key or an electronic keyer to the rear
panel CW KEY jack.
. Place the POWER switch ON.
. Place the CW key.
. Enter the desired frequency.
. Set the METER switch to ALC.
. Press the REC/SEND switch to select SEND.
The ON AIR indicator lights, showing that you
are now in the transmit mode.
7. Press the key, the ON AIR indicator lights and the
meter pointer deflects.
8. Adjust the CAR LEVEL control until the meter
deflection is within the ALC zone.
aPN
SS oe
5 I oe 1 e ee ee
NCOGLUOSQ0000000000 37009000000
power SO P SO npu TO 29o how
— ALC zone #
9. Release the key. The receive mode will be
restored and the ON AIR indicator will turn off.
H SEM! and FULL break-in
[ 1] Keyer connections
When the internal keyer is turned off and you
intend to use either a straight key or an external
keyer you should connect the plug as shown in the
accompanying diagram. Use a plug with a diameter
of 6.0 mm.
To use external straight key
+5V, Contact
Current about imA
_
A á a
Ground Notused +
or - +5V, Contact
Current about 1mA
Ground $
Notes |
1. When using a key or an external electronic |
keyer, set the MENU key to ON, select menu !
number 12 with the M.CH/VFO CH control, and ;
set the display OFF with the UP / DOWN j
switches. To restore the previous operating |
state, press the MENU key again. Initially, the
display is OFF.
2. Use of a stereo plug in this instance will cause
misoperation of the transceiver.
3, Use a shielded cable or a coaxial cable to
connect the plug and the keyer.