Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for BSLBATT Powerline 5
Summary of Contents for BSLBATT Powerline 5
- Page 1 BSLBATT Powerline -5 & VICTRON Installation Manual V 1.3...
- Page 2 DO NOT INGEST! The Terminals of the BSLBatt should always be considered live, therefore do not place tools or any other items across the terminals. Do not pierce, short or damage the terminals in any way.
-
Page 3: Table Of Contents
BSLBatt & Victron Setup-Guide Contents SAFETY GUIDELINES ............................i Contents ................................ii Pin-out Diagram ............................ 1 Battery Set-up ............................2 General ............................2 2.1.1 Turning battery on & Off ..................... 2 2.1.2 CAN Communication ......................2 2.1.3 Dry Contacts.......................... 2 2.1.4... -
Page 4: Pin-Out Diagram
BSLBatt & Victron Setup-Guide Pin-out Diagram Figure 1: Pin-out diagram for 51.2V BSL Powerline-5 Battery. Page... -
Page 5: Battery Set-Up
BSLBatt & Victron Setup-Guide Battery Set-up General 2.1.1 Turning battery on & Off The battery can be switched on or off by holding down the small, recessed button marked “RESET” for around 3 seconds. 2.1.2 CAN Communication A VE.Can to CAN-bus BMS “Type B” cable is required for CAN-Bus communication between the BSL battery and the Victron GX device. -
Page 6: Multiple Batteries
BSLBatt & Victron Setup-Guide Multiple Batteries 2.2.1 Max Number of Parallel Batteries A maximum of 15 batteries can be connected in parallel. Each battery will require a unique binary address which can be setup via the 485-1 & 485-2 ports located on the bottom of the battery. - Page 7 BSLBatt & Victron Setup-Guide Figure 2: Powerline-5 pin-out image showing 485-1 & 485-2 ports: Page...
-
Page 8: Inverter Set-Up
BSLBatt & Victron Setup-Guide Inverter Set-up Batteries Per Inverter Size 3.1.1 5.1 kWh (100 Ah) Inverter Size Recommended Batteries Minimum Batteries 15 kVA 10 kVA 8 kVA 5 kVA 3 kVA 3.1.2 6.4 kWh (125 Ah) Inverter Size Recommended Batteries Minimum Batteries... -
Page 9: Kwh (172 Ah)
BSLBatt & Victron Setup-Guide 3.1.5 8.8 kWh (172 Ah) Inverter Size Recommended Batteries Minimum Batteries 15 kVA 10 kVA 8 kVA 5 kVA 3 kVA 3.1.6 10.2 kWh (200 Ah) Inverter Size Recommended Batteries Minimum Batteries 15 kVA 10 kVA... -
Page 10: Battery Set-Up On Victron Gx Device
BSLBatt & Victron Setup-Guide Battery Set-up on Victron GX Device 1. The VE.Can to CAN-bus BMS Type B cable needs to be connected to the VE- Can port on the GX device and the second unused VE.Can port needs to be terminated with the Victron blue terminator. -
Page 11: Battery Set-Up On Victron Mppt Device
BSLBatt & Victron Setup-Guide Battery Set-up on Victron MPPT Device Page... -
Page 12: Inverter Settings (Victron)
BSLBatt & Victron Setup-Guide Inverter Settings (Victron) General Tab Total battery bank capacity Page... -
Page 13: Grid Tab
BSLBatt & Victron Setup-Guide Grid Tab Page... -
Page 14: Inverter Tab
BSLBatt & Victron Setup-Guide Inverter Tab Take note: Shutdown on SOC optional but recommended to untick, the charger source can then shutdown on voltage instead. Page... -
Page 15: Charger Tab
BSLBatt & Victron Setup-Guide Charger Tab Page... - Page 16 BSLBatt & Victron Setup-Guide Page...
-
Page 17: Assistant Tab (A)
BSLBatt & Victron Setup-Guide Assistant Tab (a) Page... -
Page 18: Assistant Tab (B)
BSLBatt & Victron Setup-Guide Assistant Tab (b) Page... -
Page 19: Assistant Tab (C)
BSLBatt & Victron Setup-Guide Assistant Tab (c) Page... -
Page 20: Assistant Tab (D)
BSLBatt & Victron Setup-Guide Assistant Tab (d) Page... -
Page 21: Assistant Tab (E)
BSLBatt & Victron Setup-Guide Assistant Tab (e) Page... -
Page 22: Assistant Tab (F)
BSLBatt & Victron Setup-Guide 4.10 Assistant Tab (f) Page... -
Page 23: Revision History
- Address 0 column removed from Dip switch settings for multiple batteries (Tables 1 and 2) - Formatting Nov 2022 P.J. Andrew - Update on BSLBatt Branding. D. E. Cornew - Formatting. - Update VE.Configure Inverter Tab. (4.3) - Update VE.Configure Charger Tab.