Technical Data; Care And Cleaning - Renkforce RF-3794904 Operating Instructions Manual

Mounting in a server rack
• The lighting unit can be installed in a 48.26 cm (19 inch) server rack. You can use the supplied
mounting hardware (screws or magnetic tape) to attach the lighting unit.
• If using the magnetic tape, make sure that the mounting surface on the lighting unit is clean
and free of dust, grease and moisture.
• Check that the magnetic tape adheres adequately to the mounting surface inside your server
rack.
Be careful not to cover or glue over the mode switch when attaching the magnetic
tape to the lighting unit.
• Switch the product to the desired mode before installation. There are two available operating
modes: Mode I - (door mode) or mode II (touch mode).
• It is recommended to check the two modes before installation. To do this, connect the round
plug of the power adapter to the socket on the lighting unit and the power adapter to a
suitable mains socket. Please also note the illustration in the section "Product overview".
Then disconnect the power adapter from the mains socket and the lighting unit.
• Use the touch mode if you want the light to switch on manually by pressing with your finger.
When installing, make sure that the sensor area is easily accessible.
• Use the door mode when the light should turn on when opening the rack door. The detection
range of the door sensor is approx. 4 – 5 cm.
• As soon as an object is located at a distance of approx. 4 – 5 cm in front of the door sensor,
the light switches off. When the object (rack door) is removed from the door sensor, the light
turns on.
• It is recommended to fix the door sensor of the lighting unit at a distance of approx. 1 cm to
the closed rack door. As shown in Figure.
• The screw holes can be covered with the supplied covers after mounting.
• After installation, connect the round plug of the power adapter to the socket on the lighting
unit and the power adapter to a suitable mains socket.
• Check the function of the lighting unit.

Care and Cleaning

• Disconnect the product from the mains socket before cleaning.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may
damage the case or cause the product to malfunction.
• Do not immerse the product in water or other liquids.
• Use a dry, lint-free cloth to clean the product.
• The LED bulbs are not interchangeable.
Disposal
This symbol must appear on any electrical and electronic equipment placed on the
EU market. This symbol indicates that this device should not be disposed of as
unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose
of it separately from unsorted municipal waste. Spent batteries and accumulators,
which are not enclosed by the WEEE, as well as lamps that can be removed from
the WEEE in a non-destructive manner, must be removed by end users from the
WEEE in a non-destructive manner before it is handed over to a collection point.
Distributors of electrical and electronic equipment are legally obliged to provide free take-back
of waste. Conrad provides the following return options free of charge (more details on our
website):
• in our Conrad offices
• at the Conrad collection points
• at the collection points of public waste management authorities or the collection points set up
by manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be disposed of.
It should be noted that different obligations about the return or recycling of WEEE may apply in
countries outside of Germany.

Technical Data

a) Lighting unit
Input voltage/current ..................... 12 V/DC, 0.25 A
Power consumption ...................... 3 W
Bulb .............................................. 30 x SMD3014 LED, not interchangeable
Luminous intensity ........................ 223 lm
Colour temperature ....................... 6500K, cold white
Protection class ............................ III
Operating conditions ..................... -20 to +45 °C, 30 – 60% RH
Storage conditions ........................ -25 to +65 °C, <85% RH
Dimensions (L x W x H) ................ 300 x 28.5 x 9.5 mm
Weight .......................................... approx. 169 g
b) Power adapter (LED converter)
Operating voltage ......................... 100 – 240 V/AC, 50/60 Hz
Output voltage/current .................. 12 V/DC 1000 mA
Output power ................................ max. 12 W
Protection class ............................ II
Cable length ................................. 1.5 m
1 cm distance
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or capturing in
electronic data processing systems) requires prior written approval from the publisher. Reprinting, also in part, is
prohibited. This publication reflects the technical status at the time of printing.
Copyright 2023 by Conrad Electronic SE.
This product contains a light source of energy efficiency class F.
*1897452_v2_0723_02_dh_m_en