Subscribe to Our Youtube Channel
Related Manuals for Nav TV UCTv 2 Series
Summary of Contents for Nav TV UCTv 2 Series
- Page 1 3950 NW 120 Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 UCTv2 + Dodge/Jeep uConnect (RA3/RA4) Dual Camera & A/V Interface NTV-KIT763 10/04/18 NTV-DOC265...
- Page 2 10/04/18 NTV-DOC265 Overview The UCTv2 series Interface integrates multiple video inputs to the factory 8.4” touch screen in compatible 2013+ Dodge and Jeep vehicles, with additional expansion options for future upgrades. UCTv2 (KIT762): Add up to 2 additional inputs (or 1 input while retaining OEM camera). UCTv2+ (KIT763): Same functionality as the standard system but includes an AVSW for audio integration (AV input).
- Page 3 10/04/18 NTV-DOC265 UCTv2 + pin out PIN # Description Color 12v (+) Constant Yellow INPUT 1: VIM Activation* --NOT USED-- Blue INPUT 3: Front CAM/Cargo Cam Pink OUTPUTs 2 & 3 (selectable) send 12v (+) with RX (not present) corresponding RCA MALE button press RCA Shield...
- Page 4 10/04/18 NTV-DOC265 Dash Disassembly (basic RAM) 1. Remove the Torx t20 screw at the right rear of the pocket on the right side of the dash. 2. Remove (2x) Torx t20 at the top of the dash. They are hidden beneath a rubber mat. 3.
- Page 5 10/04/18 NTV-DOC265 UCTv2 + Module Installation 1. After removing the factory radio, grab the provided Plug & Play T-harness and connect the female side to the factory 44-pin plug. Make certain the lock connects together securely. 2. Install A/V source and run signal/power leads into the front dash opening. Note: 12v ACC is provided from output 1 (PIN 11, white/red).
- Page 6 10/04/18 NTV-DOC265 UCTv2 + Install Diagram (adding A/V & Front CAM with OEM tailgate camera) Agreement End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase.
- Page 7 10/04/18 NTV-DOC265 UCTv2 + Programming Programming the UCTv2 + is performed in the vehicle, through the factory dash MUTE button, TUNING KNOB, and CLUSTER LCD for feedback. While in NAV-TV Press and HOLD settings mode only: (15 seconds) to Rotate clockwise (slowly, one enter NAV-TV detent/time) to...
- Page 8 10/04/18 NTV-DOC265 UCTv2 + Programming Parameters (OEM Cluster) Parameter Adjustment Description (cluster) Options NAV-TV TUNE-Next Item / Rotate TUNE knob to access different menus, press knob Settings Enter Change inwards to enter/change setting AUTO: Select this option if the vehicle has an automatic transmission GEAR AUTO / STICK...
- Page 9 10/04/18 NTV-DOC265 Programming for 2016+ Vehicles equipped with Panasonic Radios (CarPlay/Android Auto) NOTE: this procedure is NOT required if the vehicle has an OEM reverse camera installed. • For 2016+ vehicles equipped with the new Panasonic radio, if adding a rear camera, the method for activating rear-camera has changed and requires additional (startup/shut down) steps.
- Page 10 10/04/18 NTV-DOC265 UCTv2 + Force Buttons Force front camera: Press AUX: Hold both ‘SCREEN Force rear camera: & hold (2 sec) to activate OFF’ & ‘BACK’ (2 sec) Press & hold (2 sec) CIM*: Hold (3 sec) to activate (not supported for 2016s) ’13-’17 RAM, Grand Cherokee, Viper *Not supported on all models...
- Page 11 10/04/18 NTV-DOC265 UCTv2 + Camera Force Buttons (continued) • For 2016 & 2017 SRT vehicles, the radio has changed and is clearly indicative by the radio control buttons or the GUI on the touch panel. For these vehicles, use the following buttons to force video sources: VIM* Enable: Press and hold MUTE...
- Page 12 10/04/18 NTV-DOC265 UCTv2 + Operation Information Rear Camera Operation: Placing the vehicle in to reverse will automatically display any connected camera. This image will take precedence over all other images. Force Rear Camera: To force rear camera, press and hold radio ‘BACK’ button for 2 seconds.
- Page 13 10/04/18 NTV-DOC265 FAQs Q1. I can’t get into programming mode. A1. Turn off the vehicle and remove the key. Close all points of entry and use the remote to lock the vehicle. Wait approx. 5 minutes without opening or disturbing the vehicle. Unlock and cycle the ignition to the ‘RUN’ position. Make certain that the cluster is in FM radio mode before you begin programming;...
Need help?
Do you have a question about the UCTv 2 Series and is the answer not in the manual?
Questions and answers