Table of Contents
Advertisement
Temperature
Cooking time
→ "Basic operation", Page 13
Start the operation.
6.
Ventilate the kitchen while the appliance is heat-
‒
ing.
a Calibration starts. This creates a lot of steam.
a When the time has elapsed, a signal sounds. A
message appears on the display confirming that the
operation has finished.
Allow the appliance to cool down and then dry the
7.
cooking compartment floor thoroughly.
8.
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures
above 120 °C, this will damage the enamel.
Do not use the appliance if there is water on the
▶
cooking compartment floor.
Wipe away any water on the cooking compart-
▶
ment floor before operation.
Apply the following settings:
Type of heating
Temperature
Cooking time
→ "Basic operation", Page 13
8 Basic operation
8.1 Switching on the appliance
Press
to switch the appliance on.
▶
a The display shows the menu.
8.2 Switching off the appliance
Switch your appliance off when you are not using it.
The appliance will switch itself off automatically if it is
not used for a certain period of time.
Press
to switch the appliance off.
▶
a The appliance switches off. Any functions currently
in progress are cancelled.
a The time or residual heat indicator appears on the
display.
8.3 Starting the operation
You must start each operation.
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures above
120 °C, this will damage the enamel.
Do not use the appliance if there is water on the
▶
cooking compartment floor.
Wipe away any water on the cooking compartment
▶
floor before operation.
Press
to start the operation.
▶
a The settings appear on the display.
100 °C
30 minutes
4D hot air
Maximum
30 minutes
Start the operation.
9.
Ventilate the kitchen while the appliance is heat-
‒
ing.
a When the time has elapsed, a signal sounds. A
message appears on the display confirming that the
operation has finished.
Press
to switch the appliance off.
10.
Once the appliance has cooled down, clean the
11.
smooth surfaces in the cooking compartment with a
detergent solution and a dish cloth.
Clean the accessories thoroughly using a detergent
12.
solution and a dish cloth or soft brush.
Dry the appliance.
13.
→ "After using steam operation", Page 19
Note: Following a power cut, the calibrated settings are
retained.
To adjust the appliance to a new installation location
after moving house, reset the basic settings to the fact-
ory settings. Restart the calibration process.
8.4 Interrupting the operation
You can interrupt the operation and then continue
again.
To interrupt the operation, press
1.
Press
again to resume the operation.
2.
8.5 Setting the operating mode
After you have switched on the appliance, the menu
appears on the display.
1.
To scroll through the various selection options,
swipe to the left or right on the display.
Swipe right or left to scroll through the menu and
‒
other setting options.
Swipe down or up to scroll through selection
‒
lists.
To select a function, press the function on the dis-
2.
play.
a Depending on the function, possible setting values
or other tiles are available for selection.
To go back to a setting if necessary, press
3.
To change the setting values, use the digital setting
4.
ring:
Swipe over the setting ring clockwise or anti-
‒
clockwise, as required.
Or press a specific position on the setting ring.
‒
Use
to confirm the setting.
5.
Press
to start the operation.
6.
If the operation is ended:
7.
If required, you can select other settings and re-
‒
start the operation.
Basic operation en
.
.
13
Advertisement
Table of Contents
