Beko WNF 8447 ACE50 Operating Instructions Manual page 49

Main Wash
Main Wash symbol indicating that the main wash step has started
appears on the display.
Rinse
Rinse symbol indicating that the rinsing step has started appears
on the display.
Softener
Softener symbol indicating that the softener step has started
appears on the display.
Spin
Appears at the beginning of the final spin step and remains lit
during Spin and Pump special programmes.
If the machine does not pass to the spinning step, Rinse Hold
C
function might be active or the automatic unbalanced load
detection system might be activated due to the unbalanced
distribution of the laundry in the machine.
Loading door lock
There is a locking system on the loading door of the machine that
prevents opening of the door in cases when the water level is
unsuitable.
Door Locked symbol appears when the loading door is locked.
This symbol will flash until the loading door becomes ready to
open when programme completes or the machine is paused. Do
not force to open the loading door in this step. Symbol disappears
when the door is ready to open. You can open the door when the
symbol disappears.
Changing the selections after
programme has started
Switching the machine to pause mode
Press the Start / Pause / Cancel button to switch the machine to
pause mode. Pause symbol appears on the display indicating that
the machine is paused. Start symbol disappears.
Changing the speed and temperature settings for auxiliary
functions
Depending on the step the programme has reached, you may
cancel or activate the auxiliary functions; see, "Auxiliary function
selection".
You may also change the speed and temperature settings; see,
"Spin speed selection" and "Temperature selection".
Adding or taking out laundry
Press the Start / Pause / Cancel button to switch the machine to
pause mode. The programme follow-up light of the relevant step
during which the machine was switched into the pause mode
will flash. Wait until the Loading Door can be opened. Open the
Loading Door and add or take out the laundry. Close the Loading
Door. Make changes in auxiliary functions, temperature and speed
settings if necessary. Press Start / Pause / Cancel button to start
the machine.
The loading door will not open if the water temperature in the
C
machine is high or the water level is above the door opening.
Child Lock
Use Child Lock function to prevent children from tampering
with the machine. Thus you can avoid any changes in a running
programme.
You can switch on and off the machine with On / Off button
C
when the Child Lock is active. When you switch on the
machine again, programme will resume from where it has
stopped.
To activate the Child Lock:
Press and hold 2 and 4 Auxiliary Function buttons for 3 seconds.
nd th
"Con" appears on the display.
Same phrase will appear on the display if you press any
C
button when Child Lock is enabled.
To deactivate the Child Lock:
Press and hold 2 and 4
nd
"COFF" appears on the display.
Do not forget to disable the child lock at the end of the
C
programme if it was enabled before. Otherwise, machine will
not allow to select a new programme.
Canceling the programme
Press and hold Start / Pause / Cancel button for 3 seconds. Start
symbol flashes. Symbol of the step at which the programme was
cancelled remains lit. "
programme is cancelled.
If you want to open the loading door after you have cancelled
C
the programme but it is not possible to open the loading door
since the water level in the machine is above the loading
door opening, then turn the Programme Selection knob to
Pump+Spin programme and discharge the water in the
machine.
Machine is in Rinse Hold mode
Spin symbol flashes and Pause symbol illuminates when the
machine is in Rinse Hold mode.
If you want to spin your laundry when the machine is in this mode:
Adjust the spin speed and press Start / Pause / Cancel button.
Pause symbol disappears and Start symbol appears. Programme
resumes, discharges the water and spins the laundry.
If you only want to drain the water without spinning:
Just press Start / Pause / Cancel button. Pause symbol disappears.
Start symbol appears. Programme resumes and discharges the
water only.
End of programme
"End" appears on the display at the end of the programme.
Symbols of the programme steps remain lit. Auxiliary function, spin
speed and temperature that were selected at the beginning of the
programme remain selected.
49
EN
Auxiliary Function buttons for 3 seconds.
th
END
" appears on the display and the