Advertisement
CHAPTER 13
FAULT
CAUSE
1. Does not function
Mains plug not plugged in
on any
programme
Start button not pressed
No power
Electric circuit fuses failure
Load door open
Selector knob in OFF position
2. Does not load
See cause 1
water
Inlet tap turned off
3. Does not discharge
Discharge tube bent
water
Odd material blocking filter
4. Door will not open
Start button pressed in
5. Water on floor
Leak from the washer between the tap
around washing
and inlet tube
machine
6. Does not spin
The washing machine has not
discharged water
"No spin" setting
Washing load not evenly distributed
7. Strong vibrations
Washing machine not perfectly level
during spin
Transit brackets not removed
8. Display reads error
0, 1, 5, 7, 8, 9
9. Display reads error 2
No water fill.
10.Display reads error 3
No pump out.
11.Display reads error 4
Machine overfilled with water.
If the fault should persist, contact a Candy Service Centre. For prompt servicing, give the model of the washing machine, to be
found on the label placed on the cabinet inside of the porthole or on the guarantee certificate.
Important
1 The use of environment friendly detergents without phosphates may produce the following effects:
- The discharge rinse water may result cloudier due to the presence of zeolites in suspension. This does not compromise the
efficiency of the rinses.
- The presence of white powder (zeolites) on the washing at the end of the washing cycle. This does not remain incorporated in
the fabric and does not alter the colour.
- The presence of foam in the last rinse water which is not necessarily a sign of inadequate rinsing.
- The non-ionic surface-active agents present in the composition of washing machine detergents are often difficult to remove
from the washing itself and, even in small quantities, may produce visible signs of the formation of foam.
- Carrying out further rinses, in cases such as this, is not useful.
2 If your washing machine fails to function, carry out the above-mentioned checks before calling the Candy Technical Assistance
Service.
70
EN
REMEDY
Insert plug
Press Start button
Check
Check
Close load door and press start button
Select the required programme
Check
Turn on water inlet tap
Straighten discharge tube
Check filter
Release start button
Replace washer and tighten the tube
on the tap
Wait a few minutes until the machine
discharges water
Select a spin speed other than 0
Distribute the washing evenly
Adjust special feet
Remove transit brackets
Call service.
-
Check water supplies are on.
Check drain is clear.
Check drain hose is not kinked.
Turn off water supply to machine.
Call service.
Ôèpìa-èçãoòoâèòeëü íe íeceò íèêaêoé oòâeòcòâeííocòè ça oøèáêè ïe÷aòè,,
c o ä e p æ a ùè e c ÿ â ä a í í û x è í c ò p y ê ö è ÿ x , è o c ò a â ë ÿ e ò ç a c o á o é ï p a â o
yëy÷øeíèÿ êa÷ecòâa coácòâeííûx èçäeëèé, ocòaâëÿÿ íeèçìeííûìè ocíoâíûe
òexíè÷ecêèe xapaêòepècòèêè.
Ôipìà-âèpîáíèê íå íåñå íiÿêî¿ âiäïîâiäàëüíîñòi çà ïîìèëêè äpóêó, ùî ìiñòÿòüñÿ â
ю
öèõ iíñòpóêöiÿõ, i çàëèøຠçà ñîáî
ïpàâî ïîëiïøåííÿ ÿêîñòi âëàñíèõ âèpîáiâ,
ю
çáåpiãà
÷è íåçìiííèìè îñíîâíi òåõíi÷íi õàpàêòåpèñòèêè.
V˘robce se omlouvá za pfiípadné tiskové chyby v tomto návodû k pouÏití.
Dále si v˘robce vyhrazuje právo provést potfiebné zmûny na sv˘ch v˘robcích,
které nemají vliv na jejich základní charakteristiku.
Z zastrzezeniem prawa do modyfikacji technicznych i ewentualnych bäëdów
drukarskich.
The manufacturer declines all responsibility in the event of any printing mistakes in
this booklet. The manufacturer also reserves the right to make appropriate
modifications to its products without changing the essential characteristics.
Advertisement
