Advertisement
Opera ng Instru ons & Parts Manual
ATD 3- Ton Jack Pack
Service Jack Model Number: ATD-7504
Capacity
Min. Height
3 Ton
5 3/8"
-
Jack Stands Model Number: ATD-7443
Capacity
Min. Height
3 Ton
11-13/16"
Contents:
Page: 1. Speci ca ons
2. Safety & Warning Informa on
3. 4. & 5. Setup, Opera on & Preven ve Maintenance
6. Inspec on, Storage & Troubleshoo ng
7. Exploded View & Replaceable Part Numbers
8. Warranty Informa on
WARNING: This product may contain chemicals, including lead, known to the State of California
to cause cancer, birth defects or other reproductive harm. Wash hands after handling.
Jack Size
Max Height
(L x W x H)
19 1/2"
-
26 3/4" x 13 3/8" x 7 1/4"
-
Max Height
7 1
5 -
1 /
" 6
Made in China to ATD Tools, Inc. Speci cations
Visit us at www.atdtools.com
Saddle Diameter
-
-
4 5/16"
Saddle Size
Base (L x W)
- 3
/ 1
" 2
x
" 1
7-11/16" x 6-15/16"
1
Model: ATD-7500
Capacity: 3 Ton
Net Weight
-
78 LB
Net Weight
15
B L
ATD7500_rev_0417
Advertisement
Table of Contents
Related Manuals for ATD Tools ATD-7500
Summary of Contents for ATD Tools ATD-7500
- Page 1 WARNING: This product may contain chemicals, including lead, known to the State of California to cause cancer, birth defects or other reproductive harm. Wash hands after handling. Made in China to ATD Tools, Inc. Speci cations Visit us at www.atdtools.com...
-
Page 2: Safety And Warning Information
Model: ATD-7500 Capacity: 3 Ton SAFETY & WARNING INFORMATION This is the safety n c on Indicates a hazardous symbol. This symbol will n fy you situa on. If proper steps are WARNING of any poten al injury hazards. not followed, death or Please follow all instruc ons that serious injury could result. - Page 3 Model: ATD-7500 Capacity: 3 Ton SETUP, OPERATION & PREVENTIVE MAINTENANCE SETUP Prior to each use, visual inspec on (See Pg. 6) shall be made to the device by checking for abnormal condi ons, such as cracked welds, leaks, and damaged, loose, or missing parts.
- Page 4 Model: ATD-7500 Capacity: 3 Ton SETUP, OPERATION & PREVENTIVE MAINTENANCE (Cont.) LOWERING Turn the handle/release valve clockwise to the closed posi on. Do not over ghten. Pump the handle up and down to li vehicle o jack stands. Remove the jack stands and safety pins. DO NOT get under or let anyone get under the vehicle while lowering.
- Page 5 Model: ATD-7500 Capacity: 3 Ton SETUP, OPERATION & PREVENTIVE MAINTENANCE (Cont.) JACK STANDS Inspect each stand before use. Ensure all parts move freely. Only apply grease to the locking handle pivot point of this product and ensure all excess grease is wiped away before stand is used.
-
Page 6: Inspection, Storage & Troubleshooting
Model: ATD-7500 Capacity: 3 Ton INSPECTION, STORAGE & TROUBLESHOOTING INSPECTION Visual inspec on shall be made before each use of the device by checking for abnormal condi ons, such as cracked welds, leaks, and damaged, loose, or missing parts. Other inspec ons shall be made per product opera ng instruc ons. -
Page 7: Exploded View & Replaceable Part Numbers
Model: ATD-7500 Capacity: 3 Ton EXPLODED VIEW & REPLACEABLE PART NUMBERS Item Part Number* Descrip on LYD3D-100 Front wheel assembly LYD3D-101 Two Piece Handle LYD3D-102 Handle Fork Assembly LYD3D-103 Rear Caster Assembly ATD-7443 3 Ton Jack Stands W/ Safety Pin... -
Page 8: Warranty Information
WARRANTY INFORMATION ONE YEAR LIMITED WARRANTY For a period of one (1) year from your purchase date, ATD Tools Inc. will repair or replace (at its option) without charge, your ATD product if it was purchased new and the product has failed due to a defect in material or workmanship which you experienced during normal use of the product.
Need help?
Do you have a question about the ATD-7500 and is the answer not in the manual?
Questions and answers