CONTENTS 1.Introduction and Intended Use..................1 2.Important Information on Blood Pressure and its Measurement........4 3. Components of your blood pressure monitor..............6 4. Using your Monitor for the First Time................7 5.Measurement Procedure.....................10 6.Care and Maintenance....................20 7. Warranty........................21 8. Certifications.......................27 9. Technical Specifications....................21 10.
1.Introduction and Intended Use 1.2 Warnings and Precautions It enables reliable measurement of systolic and diastolic blood pressure as well as pulse Warning: The device contains sensitive electronic components. Avoid strong electrical or through the oscillometric method. electromagnetic fields in the direct vicinity of the device (e.g. mobile telephones, Before using, please read this instruction manual carefully and then keep it in a safe microwave ovens).These can lead to temporary impairment of the measuring place.
Caution: To avoid damaging the device, keep this unit away from children and pets. 2.Important Information on Blood Pressure and its Measurement Caution: The standard material used for the bladder and tubing is latex-free. Attention: Self-measurement means control, not diagnosis or treatment. Unusual values 2.1.
3. Components of your blood pressure monitor 3.1. Measuring unit Memory LCD Display Sart/Stop Batter Setting Cell Cover Picture-01 Wrist Cuff There are six grids in the display of device. Please refer to the picture-01-01. Different grids represent different interval scales of WHO. 3.2 The symbols on the LCD display 1.
3.3. Features of Model W02 Battery replacement 1.Talking function 2. Double users: 2 x 120 sets memory Low Battery Indicator 3.Date/time display 4. Irregular heartbeat checking 1.When the Low Battery Indicator appears on the display, turn the monitor off and remove 5.
Setting the Year: 5. Measurement Procedure When the year display is flashing, press the MEM button continuously and it will increase continuously 1 by 1 until 2049, and then return the original year , once the year set is OK, 5.1.
Page 8
b) After automatically reaching an individual pressure, the pump stops and the pressure slowly falls. The cuff pressure is displayed during the measurement. c) When the device has detected your pulse, the heart symbol in the display begins to blink. d) When the measurement has been concluded, the measured systolic and diastolic blood pressure values, as well as the pulse will be displayed.
Page 9
5.4. Irregular Heartbeat Detector 3.Any reading can be affected by the measurement site, the position of the PATIENT, exercise, or the PATIENT’S physiologic condition This symbol - indicates that certain pulse irregularities were detected during the 4.Performance of the AUTOMATED SPHYGMOMANOMETER can be affected by measurement.
Page 10
5.6. Error Indicates Trouble removal SYMBOL CAUSE CORRECTION No display Replace both batteries with new ones. Check the battery Weak battery or improper placement appears installation for proper placement of the battery polarities. Check if the pump is working or not. If it is working, then Sensor abnormal the problem is sensor abnormal.
Page 11
Put up The following symbols may appear in this manual, on the Digital Blood Pressure Monitor W02, or on it's accessories. Some of the symbols represent standards and compliances Keep dry associated with the Digital Blood Pressure Monitor W02 and its use.
measurements for the correct user. Pressing the Memory button again displays the 6. Care and Maintenance previous value. To view a particular stored memory, press and hold the Memory button to scroll to that stored reading. Wash hands after each time measurement. 5.7.
9. Technical Specifications 7. Warranty Model: W02 Your blood pressure monitor is guaranteed for 1 year against manufacturers’ defects for Weight: 101g (Batteries are not included) the original purchaser only, from date of purchase. The warranty does not apply to Display: 41.5*49.5mm 【1.63"x1.95"】LCD Digital Display...
30 cm (12 inches) to any part of the Blood CISPR 11 Pressure Monitor (model: W02), including cables specified by the manufacturer. Otherwise, degradation of the performance of this equipment could result.
Page 15
Table 3 Table 2 Guidance and manufacturer’s declaration - electromagnetic Immunity Test IMMUNITY Band Modulation Distance Guidance and manufacturer’s declaration - electromagnetic Immunity Frequency Service MoModulation TEST LEVEL (MHz) (MHz) (V/m) Immunity Test IEC 60601-1-2 Test level Compliance level 380-390 TETRA 400 Pulse Modulation 18 Hz Electrostatic discharge (ESD)