CONTENTS 1. Introduction and Intended Use....................3 2. Important Information on Blood Pressure and its Measurement...........5 3. Components of your blood pressure monitor.................7 4. Using your Monitor for the First Time..................8 5. Measurement Procedure..................... 9 6. Care and Maintenance......................16 7. Warranty..........................16 8.
1.Introduction and Intended Use The device is intended to measure systolic and diastolic blood pressure as well as the pulse by wrapping around the wrist with cuff circumference ranging from 13.5cm to 19.5cm . The device is used for adult that age is more than 12 years old ,and the intended populations are the patients with hypertension or need blood pressure monitoring.The device is not used for patients under dialysis therapy or on anticoagulant, antiplatelets, or steroids.
Page 5
• Don’t place the cuff over wound part. • Pressurization of the CUFF can temporarily cause loss of function of simultaneously used monitoring ME EQUIPMENT on the same limb. • Apply CUFF and its pressurization to any limb where intravascular access or arteriovenous (A-V) shunts exist, can temporarily interfere with blood flow and may cause injury to the patient.
and do not drape tubing around your neck. Caution: To avoid damaging the device, keep this unit away from children and pets. Caution: The standard material used for the bladder and tubing is latex-free. Attention: Self-measurement means control, not diagnosis or treatment. Unusual values must always be discussed with your doctor.
Page 7
Picture-01 There are six grids in the display of device. Please refer to the picture-01-01. Different grids represent different interval scales of WHO. Picture-01-01 Blood pressure is very high if your diastolic pressure is above 90 mmHg and/or your systolic blood pressure is over 160 mmHg, while at rest.
10. Pulse display 11.WHO symbol 12. Memory symbol 13. Diastolic blood pressure 14.Systolic blood pressure 3.3. Features of Model W02 1. Talking function 2. Double users: 2 x 120 sets memory 3.Date/time display 4. Irregular heartbeat checking 5. Average value function 6.
Setting the Year: Initial year is 2019, when the year display is flashing, press the memory button, the year will increase by I year each, hold the memory button and it will increase continuously 1 by 1, until 2049, and then rollover to 2019, once the year Setting is OK, press SET button to confirm. Setting Month/Date: Initial Month/Date is 1/01, when the Month display is flashing, press the memory button, the month will increase by 1, press SET button to confirm, and do in the same way to set the date.
Page 10
blood pressure will be measured ! Note: Only use approved cuffs! • A loose cuff or a sideways protruding air pocket causes false measurement values. • With repeated measurements, blood accumulates in the wrist, which can lead to false results. Consecutive blood pressure measurements should be repeated after a 1 minute pause or after your wrist has been held up in order to allow the accumulated blood to flow away.
Page 11
upturned. Make sure wrist is in correct position, to avoid body movement. Sit still and do not talk or move during the measurement. After the cuff has been appropriately positioned on the wrist and connected to the blood pressure monitor, the measurement can begin: a) Press the Stop/Start button.
Page 12
5.5. Irregular Heartbeat Detector This symbol - indicates that certain pulse irregularities were detected during the measurement. In this case, the result may deviate from your normal basal blood pressure – repeat the measurement. Information for the doctor on frequent appearance of the Irregular Heartbeat Symbol This instrument is an oscillometric blood pressure monitor device that also analyzes pulse frequency during measurement.
Page 13
5.7 Trouble shooting 5.8 SYMBOL DESCRIPTIONS The following symbols may appear in this manual, on the Blood Pressure Monitor W02, or on it's accessories. Some of the symbols represent standards and compliances associated with the Blood Pressure Monitor W02 and its use.
Page 14
Manufacturer Specifies serial number Type BF applied part Direct current DISPOSAL: Do not dispose this product as unsorted municipal waste. Collection of such waste separately for special treatment is necessary. Follow instructions for use Put up fragile Keep dry Avoid the sun handle gently temperature range 5.9.
5.11. Battery Change Indicator Batteries discharged– replacements required When the batteries are discharged, the battery symbol will flash as soon as the instrument is switched on. You cannot take any further measurements and must replace the batteries. The battery compartment is located on the back side of the unit a) Remove cover from the bottom plate, as illustrated below picture-06 b) Insert the batteries (2 x size AAA ).
times is 390 times during the shelf life. a) Do not expose the device to either extreme temperatures, humidity, dust or direct sunlight. b) The cuff contains a sensitive air-tight bubble. Handle this cuff carefully and avoid all types of stress through twisting or buckling.
Model: W02 Wight: 103g (batteries and AC adapter is not included) Display: 49.5 x 41.5mm LCD Digital Display Size: 68 (W) x 68 (L) x 30 (H) mm Accessories: 1×Main Device, 1×Cuff, 1×Users manual, 1×Warranty card Operating Conditions: Temperature: 5℃ to 40℃;Humidity: 15% to 93% RH;...
Page 18
The device is intended for use in the electromagnetic environment specified below. The customer of the user of the device should assure that it is used in such an environment. Emission test Compliance Electromagnetic environment – guidance use RF energy only for its internal function. device RF emissions Therefore, its RF emissions are very low and are not...
Page 19
Guidance and manufacture’s declaration – electromagnetic immunity The device is intended for use in the electromagnetic environment specified below. The customer or the user of device should assure that it is used in such an environment. Electromagnetic environment - Immunity test IEC 60601 test level Compliance level guidance...
Page 20
is intended for use in the electromagnetic environment specified below. The customer or the user device of the should assure that it is used in such an environment. device Immunity IEC 60601 test Compliance Electromagnetic environment - guidance test level level Portable and mobile RF communications equipment should be used no closer to any part of the device,...
Page 21
additional measures may be necessary, such as re-orienting or relocating the device. Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m. Recommended separation distances between portable and mobile RF communications equipment and the device The device is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.
The MANUFACTURER should consider reducing the minimum separation distance, based on RISK MANAGEMENT, and using higher IMMUNITY TEST LEVELS that are appropriate for the reduced minimum separation distance. Minimum separation distances for higher IMMUNITY TEST LEVELS shall be calculated using the following equation: Where P is the maximum power in W, d is the minimum separation distance in m, and E is the IMMUNITY TEST LEVEL in V/m.