Battery Charging - Lavorwash Clean Track NANOscrub Evo 50 cbt Instructions Manual

2 Water outlet adjusting lever
3 Brush plate lift/lower lever
4 Squeegee lift/lower lever
5 Brush operation lever
6 Recovery tank drain hose
PHOTO C MODEL B - (DC 24V)
1 Brush motor switch
1A Brush motor operation led
2 Suction motor switch
2A Suction motor operation led
3 Battery power test
3A Green led - full battery charge
3B Yellow led - 50% battery charge
3C Red led - battery discharged
PHOTO D MODEL B - (DC 24V)
1 General on / off key switch
2 Brush operation lever
3 Brush plate lift/lower lever
4 Squeegee lift/lower lever
5 Brush motor thermal breaker
6 Recovery tank drain hose
7 Battery connector
8 Water outlet adjusting lever
PHOTO E MODEL BT/T - (DC 24V WITH TRACTION)
1 Battery power test
1A Green led - full battery charge
1B Yellow led - 50% battery charge
1C Red led - battery discharged
2 Forward/reverse indicator
3 Reduce speed switch
3A Traction speed 1
3B Traction speed 2
3C Traction speed3
3D Traction speed 4
4 Increase speed switch
5 Brush motor switch
5A Brush motor operation led
6 Suction motor switch
6A Suction motor operation led
PHOTO F MODEL BT/T - (DC 24V WITH TRACTION)
1 General on / off key switch
2 Forward/reverse traction operation lever
3 Brush plate lift/lower lever
4 Squeegee lift/lower lever
5 Brush motor thermal breaker
6 Traction motor thermal breaker
7 Recovery tank drain hose
8 Battery connector
9 Water outlet adjusting lever
PHOTO G MODEL B - BT/T - (DC 24V WITHOUT
AND WITH TRACTION)
1 Battery compartment opening lever
2 Solution tank filling opening
PHOTO H MODEL B - BT/T - (DC 24V without and
with traction)
Battery connection diagram
PHOTO I MODEL B - BT/T - (DC 24V without and
with traction)
1 Opening clip spring
2 Battery compartment with 12v Batteries
3 Battery connection wiring
PHOTO L MODEL B - BT/T - (DC 24V without and
with traction)
1 Built-on battery charger
2 Battery charger power supply cable
PHOTO M MODEL E - B - BT/T
1 Squeegee bumper wheel
2 Squeegee pression adjusting knob
3 Suction hose
4 Squeegee blades replacement knob
5 Squeegee wheel
6 Squeegee fixing knob
7 Squeegee inclination adjusting knob
PHOTO N MODEL E - B - BT/T
1 Hood of suction filter compartment
2 Solution tank filling opening
3 Recovery tank
4 Solution tank
PHOTO O MODEL E - B - BT/T
1 Floating device
2 Suction filter
3 Recovery tank inspection
PHOTO P MODEL E - B - BT/T
1 Solution water filter
5.3.

BATTERY CHARGING

Connect the patch cord to the power cable of the bat -
tery charger ( Photo L - 2 ) and to the mains power.
On switching on the battery charger will check the
battery voltage and decide whether to start the
charging process. If the battery is not connected to
the battery charger, the red LED will flash. If the result
of the test is positive after 1 second the charging of
the battery can start, with the red LED on.
During the charging process, remember to keep the
upper tank elevated for proper ventilation.
The progress of the charging process is shown by
three LED's: red, yellow and green, as in the whole
range of the battery chargers.
The green LED shows the end of the charging or the
last phase in case of deep charging process; in the for-
34