FOTILE EMG9030 - Wall Mount Range Hood with Touchscreen in Stainless Steel Manual

SAFETY INFORMATION

Product features and specifications are subject to change, at any time, without notice. Please visit our website at www.fotileglobal.com for the most up-todate information. In order to ensure the safe and efficient use of Fotile appliances, please take note of the following types of highlighted information that will be outlined throughout this manual:

IMPORTANT NOTE
highlights information that is particularly important.

signals a situation where minor injury or product damage may occur if instructions are not followed.

states a specific hazard that may cause serious injury or death if precautions are not followed.

In order to prevent accidental damage to the Fotile Range Hood and/or bodily injuries as a result of its operation, please read the following safety informationinstalling and/or using this appliance. Following the instructions carefully will significantly reduce the risk of fire, electric shock and/or bodily injuries to persons. We recommend that you keep this manual for future use and/or in case of transfer of ownership of the range hood.

Important Note:

• This appliance is intended for indoor home cooking only; it cannot be used for outdoor cooking.
• Check the appliance for damage after unpacking it. If you detect any obvious damage to the product, do not proceed with the installation. Please contact our authorized service center immediately.
• Avoid placing gypsum powder, construction dust, etc. within close proximity of the range hood.
• Operate the range hood only in the manner outlined in this product manual.
• When operating the range hood, do not leave the appliance unattended. If you have any questions and/or concerns, please contact our authorized service center.
• Operate, clean and maintain the range hood in accordance to the instructions outlined in this manual.
• Clean the metal oil filter and wing-like plate according to actual conditions.
• The range hood's motor has a thermal overload function, which automatically turns off the motor when it overheats. Once the motor cools down, the range hood will automatically restart. If the motor, continually turns off and restarts, please contact our authorized service center.
• If the range hood has not been in operation for an extended period of time, unplug the appliance.
• Please make sure correct installation and maintenance of the appliance. Installation work and electrical wiring must be done by qualified person(s), in accordance with all applicable codes and standards, including firerated construction codes and standards. The installation personnel should be responsible for normal operation of the appliance at the installed position.
• When operating the range hood in exhaust mode, ensure to install the damper along with the hood.
• For general exhausting only. Do not use this range hood to exhaust hazardous and /or explosive materials or gas.
• In order to reduce the risk of fire, all exhaust pipes, flues and devices should be nonflammable. Use only metal duct cover and metal duct pipes. Never cover the hood with flammable plastic film or paper.
• Services guaranteed under warranty must be performed by Fotile certified service provider or personnel.
• Please read the specification label on the range hood for further information and requirements.

• When applicable local regulations comprise more restrictive installation and/or certification requirements, the aforementioned requirements will prevail, and installation personnel must conform to these requirements.
• The operating temperature of the range hood should not exceed 104 ℉ (40℃ ).
• Please do not place anything on top of the product. Anything placed on top may fall off or incline. For example, if you place seasoning bottles on top, the inclination may cause liquid to flow inside the product, resulting in damaged electrified components and therefore unnecessary risks. Our company will not bear the responsibility for free repair in case of product damage due to the above reason.
• Clean the Grease Cup frequently to prevent overflow. The resulting grease is inedible!
• When cutting or drilling into the wall or ceiling, be careful not to damage electrical wiring, water pipes, gas lines, or other hidden utilities.
• Adhere to the heating equipment manufacturer's guidelines and safety standards, such as those published by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities. Meanwhile, conform to the safety standards issued by such administrative departments as fire department.
• When gas burners are in operation without any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Only operate the gas burners with cookware on them.
• Adhere to the voltage and frequency settings listed in this manual to avoid possible damages to the range hood.
• Please use standard accessories provided by our company to prevent the range hood from falling down accidentally. The hole drilled in the wall should precisely match the size of the expansion pipe, otherwise, the range hood may loose and fall down.
• Tampered glass is applied to the products of the company and the tampering treatment of the glass determines the extremely little possibility of spontaneous explosion. If the occurrence of spontaneous explosion is not due to improper use, our company promises free replacement of the accessories.

Risk of Electric Shock

A defective appliance may cause electric shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box in case of problems, and contact our authorized service center.

• The range hood should be connected to a standard power socket with safe grounding. Midway connection, prolonged electric line or multi-socket wiring may cause electric shock, overheating and, in some cases, result in a fire. Installation of the range hood should be performed by professional electricians in strict accordance with electricity standards and regulations of the local area. Before connecting the rod, turn off the power source and take appropriate measures to prevent auto closing of the power switch.
• In order to prevent electric shock and/or other bodily injuries to persons, do not exceed 120V AC input.
• Do not install the range hood in a bathroom and/or a humid area, as this will significantly increase the risk of electric shock.
• If a wire is damaged or defective, contact an authorized service provider or a qualified technician (provided by Fotile) to replace the wire.
• Do not change, stretch, knot, pressure or squeeze the wire as any resulting damage can result in electrical and/or fire hazards.
• Prevent water from coming into contact with the range hood's electrical components, such as the motor, switch and connector. Do not wash the appliance with water. Do not use the appliance if it is wet, as electric leakage and/ or electric shock may occur.
• Do not attempt to change the range hood's internal wiring system. Improper modifications and/or repairs to the internal wiring can result in bodily injuries to persons, electric shock and/or a fire.
• In order to avoid electric shock, remember to turn off the appliance's power source before installation, cleaning and/or maintenance service.
• Avoid using high-pressure detergents and/or steam cleaners on the appliance, as they may result in electric shock.
• Do not touch the plug or switch with wet hands, as an electric shock may occur.

Grounding Instructions

• This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.
• Improper grounding can result in electric shock.
• Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.
• Do not use an extension cord. If the power supply cord is too short, have a qualified electrician install an outlet near the appliance.

Risk of Fire

• In order to reduce the risk of fire and to properly exhaust air, always duct the air outside. Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces and/ or garages.
• In order to prevent the risk of fire, the range hood should be operated and maintained in accordance to the instructions.
• Hot oils may ignite and burn quickly. Never leave hot oils unattended.
• Please regularly clean the oil filter and wing-like plate, since there is a fire hazard from grease collecting in the oil filter and wing-like plate.
• Never operate the product without the oil filter and wing-like plate.
• Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heat-producing appliance for solid fuel (e.g. wood or coal).There must be no flying sparks.
• Avoid cooking with food products that produce flames under the range hood.

To Reduce Risk of Cooktop Grease Fire:

1. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.
2. Always turn the hood on during cooking.
3. Clean ventilating fans. Grease should not be allowed to accumulate on fan, filter or in exhaust ducts.
4. Use proper pan size. Always use cookware appropriate for the size of the surface element.

To Reduce the Risk of Injury to Persons in the Event of a Range Top Grease Fire, Observe the Following:

• Smother flames with close-fitting lid, cookie sheet, or metal tray, then turn off the burner. Be careful to prevent burns. If the flames do not go out immediately, evacuate and call the fire department.
• When the cooking utensil catches fire, switch off the range hood immediately. Effective extinguishing measures must be taken at once, such as covering the open flame with metal cover, turning off the master gas valve and keeping flammable substance from the open flame etc.
• Never pick up a flaming pan—you may be burned.
• Do not use water, including wet dishcloths or towels—a violent steam explosion will result.

Use an Extinguisher Only If:

• You know you have a class ABC extinguisher and you already know how to operate it.
• The fire is small and contained in the area where it started.
• The fire department is being called.
• You can fight the fire with your back to an exit

Risk of Injury

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
• The range hood may have sharp edges. Be careful to avoid cuts and abrasions during installation and cleaning. Do wear qualified protective gloves.
• The accessible parts become very hot when in operation. Never touch hot parts. Keep children at a safe distance.
• Do not touch lamps during or soon after operation. Burns may occur.
• Do not insert your limbs and/or foreign objects into the impeller while the range hood is in operation, as that action might cause injury.
• This appliance is not intended for operation with an external clock timer or a remote control.
• Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained aftersales technicians.
• If any abnormalities and/or defects occur while operating the range hood, immediately turn off the appliance and unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Then, contact our authorized service center. Abnormal operation and defects may cause hazardous situations, such as electric shocks and fires.
• This product contains chemicals known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, please go to: www. P65Warnings. ca.gov

Risk of Suffocation:

• Packaging material is dangerous to children. Never allow children to play with packaging material, which may cause suffocation. Keep all packing material out of proximity to children. Please remember that packaging materials should not be treated as toys.

Risk of Death:

• Risk of poisoning from flue gases that are drawn back in.
• Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as room air-dependent heat-producing appliance is being operated.
  Exhaust gases through the flue (chimney) of fuel burning equipment to prevent back drafting.
• Fotile is not responsible for injuries caused by improper and/or incorrect operation of the range hood.

OPERATION

1. Do not use excessive force to press buttons on the control panel.
2. Turn off gas burners without any cookware placed on them.
3. Do not disassemble the appliance with power on and/or without complying with instructions.
4. Clean the Grease Cup frequently to prevent overflow and a potential fire.
5. Disassembly and/or servicing of the range hood must be performed by qualified technicians.
6. Do not let the stove fire burn the range hood directly.

Product Information

Model	EMG9030
Net weight	76 lbs(34.5 Kg)
Voltage/Frequency	120V/60Hz
Rated power input of the range hood	262 W (light power included 2W × 2 )
Speed	Superhighsetting	Highsetting	Mediumsetting	Lowsetting
CFM(HVI)	690	540	440	290
Noise(sones)	7.0	5.0	3.1	1.0
Noise(dB(A))	56.5	51.5	49.5	40.5
Max static pressure (Pa)	690

1. dB noise in the above table complies with the IEC60704 standard, it is the sound pressure level, the corresponding sound power level is: 70.5dB(A) for supper-high-setting, 65.5dB(A) for high-setting, 63.5dB(A) for mediumsetting and 54.5dB(A) for low-setting.
2. The noise --Sones -- in the above table is tested in accordance with HVI-915-2015 in HVI-accredited laboratories in American.
3. Such parameters as air volume and noise may have a deviation of less than 10%.

HVI-2100 CERTIFIED RATINGS comply with new testing technologies and procedures prescribed by the Home Ventilating Institute, for off-the-shelf products, as they are available to consumers. Product performance is rated at 0.1 in. static pressure, based on tests conducted in a state-of-the-art test laboratory. Sones are a measure of humanly-perceived loudness, based on laboratory measurements.

Application Method

Operation Interface

Calibrate the Machine and Function Description

1. Power Button
   When the machine is off, press to enter stand-by mode. The machine will be automatically shut down in 2 minutes if no further operations are started. In working/ standby mode, press to stop all functions. When the power button is turned on, the following functions will be activated.
2. Cleaning Mode Button
   1. Press , then the wing-like surround suction plate will open at the lowest position and enter cleaning and maintenance mode. Press again, and the wing-like surround suction plate returns to the highest position.
   2. You can't choose to press the discharging and cleaning button with at the same time. If any one of the three function buttons is turned on, pressing cleaning button will quit the corresponding function mode; are invalid when in cleaning and maintenance mode.
3. Delayed Power Off Function
   1. Clock setting: In standby mode, press and hold to enter time setting mode; the hour digits will begin to blink; click to increase the hour number; if there is no further operation, the hour digits will stop blinking within 3 seconds; The hour setting is completed. Then the minute digits will begin to blink; click to increase the minute number; if there is no further operation, the minute digits will stop blinking within 3 seconds; the minute setting is complete. The time setting is finished.
   2. The set time will be retained. During the time setting, you can press any other key to exit time setting mode.
   3. As for the delayed power off function, there are three modes that you can choose from. The corresponding countdown periods, respectively, are 2 minutes, 5 minutes, and 10 minutes. Press for the first time in the working mode, the screen will display 02:00; press again, it will display 05:00; then if you press once again, it will display 10:00 and start counting down after 2 seconds. After the delay is completed, all functions are turned off and enter shutdown mode
   4. In the process of setting the delay time, you can cancel the delayed power off function by pressing any button.
   5. You can forcibly shut down/turn on the clock display in shutdown mode by pressing and holding in shutdown mode.
4. Lighting Button
   Press , the light will turn on; press again, the light will turn off.
5. Intelligent Air Management Button
   Press , the light band will blink orange. The indictor will turn orange. The range hood will enter intelligent air quality testing mode.
   1. If air quality is good, the light band will be green and the motor will not run.
   2. If the air quality is moderate, the light band will be orange, the wing-like surround suction plate will go down to the middle position, the motor will run at a low-speed gear.
   3. If the air quality is bad, the light band will be red, the wing-like surround suction plate will go down to the middle position, the motor will run at an intermediatespeed gear.
6. High-speed gear button, intermediatespeed gear button and low-speed gear button
   Press , the window will display "P2", the motor will run at an intermediate-speed gear, the wing-like surround suction plate will go down to the middle position.
   Press again, the window will display "P3", the motor will run at a high-speed gear, the wing-like surround suction plate will go down to the lowest position.
   Press again, the window will display "P0", the clock will be displayed in 3 seconds. The motor and the wing-like surround suction plate will be turned off.
   Press again, the window will display "P1", the motor will run at a low-speed gear, the wing-like surround suction plate will go down to the middle position.
   Note: Every time you switch in order, the default order will be P2-P3-P0-P1 when the motor is turned on. Hence, the motor will start from the previous gear state from when you turned off the motor.
7. Automatic Function
   Press , "Automatic" is displayed in the window, and the range hood enters the automatic cruise supercharging system. The range hood will automatically adjust the required airflow, wind pressure and the position of the wing-like surround suction plate according to the current smoke amount and the current resistance in the exhaust pipe to achieve the best smoke extraction effect.

Note:

1. When " " is displayed on the screen, this indicates that the range hood has detected large smoke extraction resistance.
2. When is displayed on the screen, this indicates that the range hood has detected large amounts of smoke.
3. Do not let oil stains permeate the surfaces of the range hood for long periods of time.
4. If any saline solution, disinfectant, bleach or other cleaners are spilled onto stainless steel panels (most of which contain harmful chemicals), please immediately wipe them off with a damp cloth and then clean up with a dry cloth.
   The instantaneous reduction of odor should meet the standard limits of IEC (61591).

CLEANING AND MAINTENANCE

Important Note:

Reattach the oil filter and wing-like plate after cleaning and maintenance of the range hood. Do not operate the appliance without the oil filter and wing-like plate, as it may cause safety hazards.

Risk of demager due to corrosion.

• Always switch on the appliance while cooking to avoid condensation. Condensate can produce corrosion damage.
• Surface damage due to incorrect cleaning. Clean stainless steel surfaces in the direction of the grain only. Do not use any stainless steel cleaners for operator controls.
• Surface damage due to strong or abrasive cleaning agents.
• Replace faulty LED lights to prevent the remaining lights form overloading.

• The range hood should only be cleaned as instructed; otherwise, it may ignite.
• Please remember not to wet the motor and/or the control panel, as it may result in damaging the electric circuits or potential hazards.
• Do not clean the appliance with chemical agents, such as gasoline, acids, benzene and solvents.

Risk of Electric Shock:

• Penetrating moisture may result in an electric shock. Prior to cleaning and maintenance, pull out the mains plug or switch off the circuit breaker in the fuse box.
• Do not use any high-pressure cleaners or steam cleaners, which can result in an electric shock.

Risk of Fire:
Grease deposits in the oil cup, wing-like plate and oil filter may catch fire.

Risk of Injury:

• Unplug the appliance from the mains or switch off the circuit breaker in the fuse box before installation, cleaning, maintenance and repair in order to avoid electric shock.
• The range hood may have sharp edges. Be careful to avoid cuts and abrasions during installation and cleaning. Do wear qualified protective gloves.
• While the range hood is in operation, do not insert your hand into the area housing the fan.
• The appliance will become hot during operation, especially near LED lights. Allow the appliance to cool down before cleaning. Do not touch lamps during or soon after operation. Burns may occur.
• If you would like to schedule a deep cleaning for your appliance, please contact our authorized service center.
• Fotile suggests that you clean the surface of the appliance for better use.
  1. Neutral detergent may be used to clean stains on the range hood. However, avoid touching the control panel. Wipe some detergent on the stains and let the detergent sit. Do not let the detergent sit for an extended period of time, as it can cause damages to the appliance's surface. Then, wipe off the stain with a soft cloth and the left detergent with a slightly wet cloth. Next, use another cloth to dry the appliance.
  2. Stains on the range hood should be cleaned within a short time period, as to prevent the stains from becoming permanent.
  3. Abrasive detergents, such as a salt solution, disinfectant or bleach powder cannot be used to clean the appliance. Wipe off the detergent with a wet, soft cloth. Next, use another cloth to dry the appliance.

Do not clean the appliance with abrasive tools, such as steel wool, brushes, and coarse cloths, as these materials will permanently scratch the surface of the hood.

Preparations before Cleaning:

1. Unplug the appliance.
   
2. Clear the cookware on the burners.
3. Prepare a neutral detergent and a soft cloth (or soft brush) for stain removal and cleaning.
   

Clean the range surface, oil cup, oil filter and wing-like plate.: (The cleaning can be done by the user)

1. Clean the surface of the range hood.
   
2. Remove the Grease Cup and clean it.
   
   
   For the safety of you and your family, please regularly clean the oil accumulated in the Grease Cup and deposits on the Grease Cup surface. Do wear qualified protective gloves.
   
3. Push the power button, then push the cleaning button and lower the wing-like plate.
   
   
4. Pull both front sides of the wing-like plate with two hands, pull downward and the winglike plate will be discharged. Press the buckles of the oil filter with your thumb, pull downward and the oil filter can be discharged.
   

Suggestion: In order to protect the health of you and your family, the filter should be cleaned regularly and it is dishwasher safe for your convenience.

Replacing LED Lights:

1. Unplug the appliance.
   
2. Use a small flat-head screwdriver to gently pry the LED assembly out.
   
   
3. Disconnect the wires and then replace the LED lights.
   

Use type lamp is self-ballasted fluorescent reflector lamp - Integral induction type ballast.

• Max wattage: 2W
• Voltage range: 9-10V
• Dimensions: width 5 15/16"(149.5mm)/depth 2"(49.5mm)/height 5/8"(15.5mm)

Risk of Electric Shock:
Before changing the LED lights, unplug the appliance from the mains or switch off the circuit breaker in the fuse box.

FAQ

Risk of Electric Shock

• Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by our authorized service center, or certified electricians.
• If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact our authorized service center.
• Before changing LED lights, unplug the appliance from the mains or switch off the circuit breaker in the fuse box.
• If any abnormalities and/or defects occur while operating the range hood, immediately turn off the appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box and check the following:

Problem/Issue	Possible Cause
After the POWER button is pressed, the range hood remains off and the button does not illuminate.	The appliance may be unplugged
The motor works, but the control panel buttons do not illuminate.	LED lights have been damaged

If the problem/issue with the appliance still persists after ruling out the possible cause(s), please contact our authorized service center for assistance.

SERVICE INFORMATION

• If any abnormalities and/or defects occur while operating the range hood, immediately turn off the appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Please contact our authorized service center.
• The appliance must only be repaired by professionally trained and certified technician; otherwise, severe injuries may occur.
• Warranty service is not provided based on the following situations:
  1. Failing to show invoice issued by authorized agents.
  2. Damages of the parts due to the abused and wrong installation, improper use, improper location, carelessness or other factors.
  3. Repair and maintenance without the permission of FOTILE authorized agents.
  4. Other situations that can't be controlled by FOTILE authorized agents.

In above case, FOTILE will be released from any responsibilities for the loss of personal property, personal injury directly or indirectly caused by the product.

INSTALLATION

Installation Instructions

Important Note:

• Prior to installation, please read the Fotile Range Hood Installation carefully and save it for the local inspector's future reference.
• This appliance must be installed in accordance with National Electrical Codes, as well as all state, municipal and local codes.
• The appliance must be equipped with safe circuit breaker and installed with safe grounding.
• The correct voltage, frequency and amperage must be supplied to the appliance according to the proper voltage, frequency and amperage ratings listed on the product rating plate.
• This installation must be completed by Fotile authorized service center, or certified installers.
• Please record the model number and serial number before installing the range hood. The model number and serial number are listed on the product nameplate on the range hood.
  

• Please carefully read all instructions prior to installation. Please give special consideration to the following items:
  1. If you are renovating your kitchen, be careful to not expose the exterior of the range hood. Building materials, dust, paint, coating, and gases will corrode and tarnish the surface of the range hood. It is recommended that you install the range hood after all renovations are completed.
  2. If you need to remove your gas burner before installation, please turn off the main gas valve first.
  3. Do not connect the range hood duct to a duct used to exhaust hot air or fumes from another appliance.
  4. Two installers are recommended due to the large size and heavy weight of the range hood. Since the installation is complex and the appliance is heavy, professional installers are required to install the appliance as outlined in this manual.
  5. After the appliance fixed, the plug should be accessible.
  6. Make sure to keep the appliance horizontally.
  7. Ensure that the appliance functions normally after the installation is complete.

• In order to reduce the risk of fire, electric shock, or injury to persons, please carefully read the following:
  1. The installation and wiring of the appliance should only be carried out by a professional electrician in accordance with current national or local electric safety regulations, including fire-rated construction. Non-professional personnel should not conduct installation. Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the Fotile warranty.
  2. Please use standard installation equipment and tools provided by Fotile to ensure safe installation. Make sure to use the expansion tube and expansion bolt provided by our company, in case the range hood falls down accidentally. The hole drilled into the wall should precisely match the size of the expansion tube, otherwise the range hood will not be properly secured to the wall and may fall down.
  3. The range hood should be connected to a standard power socket with safe grounding. The midway connection, prolonged electric line or multi-socket wiring may cause electric shock, overheating and even fire. Power off before wiring and make sure proper measures have been taken to avoid unexpected connection.
  4. During installation, switch off the circuit breaker in the fuse box during installation. If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.
  5. The appliance should only be installed, removed and maintained by qualified technicians to prevent risks like electric shocks, falling or fires from occurring.

Risk of Injury:

• Unplug the appliance from the mains or switch off the circuit breaker in the fuse box before installation, cleaning, maintenance and repair in order to avoid electric shock.
• The range hood may have sharp edges. Be careful to avoid cuts and abrasions during installation and cleaning. Do wear qualified protective gloves.

Warning Before Installation

• Prior to installation, ensure that the exhaust outlet is free of debris, as they may damage the range hood.
• A straight and short ducting run will ensure a high performance of the range hood.
• A curving and long ducting run should be avoided, as it will lower the performance of the range hood.
• Strictly seal the connection between the duct and duct hole with duct tape. Ensure that the connection between the duct and the duct cover is secure, and seal it with aluminum tape.
• A small duct hole will lower the performance of the range hood. Therefore, it is highly recommended that you cut a duct hole equal to or larger than 6" of the size.

Product Dimensions

Wall Preparation
The wall should be strong enough to support the range hood. As for hollow wall or hollow plate, The minimum thickness of the lumber should be 13/16" (30mm). As for concrete wall, the installation can be directly operated. The range hood should be firmly fixed on the wall.

Ductwork Installation

Risk of Injury:

• Unplug the appliance from the mains or switch off the circuit breaker in the fuse box before installation, cleaning, maintenance and repair in order to avoid electric shock.
• The range hood may have sharp edges. Be careful to avoid cuts and abrasions during installation and cleaning. Do wear qualified protective gloves.
• When cutting or drilling into walls or ceilings, do not damage electrical wiring and other hidden utilities.
• Ducted fans must always be vented to the outdoors.
• To reduce the risk of fire and to properly exhaust air, always duct air outside. Do not vent exhaust air into spaces within walls, ceilings, into attics, crawl spaces or garages.

List of Accessories

Packing List

Standard Configuration
Product	1
Hook	1
Decorative Cover	1
Oil Cup	1
Decorative Cover Hook	1
Upper Sealing Gasket	1
Operation Manual	1
Wing-like Plate Subassembly	1
Anti-collision Components	2
Metal Outlet Housing	1
Outer Net	1
Expansion Tubes for Tiles φ5.3×32mm	6
Expansion Tubes for Plasterboards φ4×40mm	6
Hook Screw ST4.2×36mm	6
Wood Screws ST5×65mm	4
Cruciform-slot Pan-head Thread-forming Screw M4×12	8
Cruciform-slot Pan-head Thread-forming Screw ST2.9×19 Zinc Coating	2
Cruciform-slot Large-brazier head Thread-forming Screw M4×8 Zinc Coating	2

Installation Tools

Installation Instructions

Safety Precautions

Special state: In order to guarantee safety and proper usage, this product (including outlet pipe and other components) must be installed and worked on by specialized technicians designated by our company. Malfunction caused by maintenance and installation from persons who are not designated by our company will not be coveredv under free maintenance of the range even if the product is still under warranty.

Before installation, please read all instructions carefully. Please pay special attention to the following notices:

1. If you are remodeling the kitchen, please do not expose the range hood to the outside, since construction materials, dust, oil paint, coating and the corresponding gas volatilized by these materials will lead to corrosion and tarnish on the surface of the range hood. The range hood should instead be installed after the kitchen remodel is complete.
2. The installation should be completed by professional installation and maintenance personnel, since the installation procedures are complicated and the machine is heavy.
3. The range hood has sharp edges, please wear gloves when you are going to move, install, clean or fix it.
4. Please do not damage electric wire or hidden devices when you drill holes in the wall; do not plug into an electric power supply when you install the machine; Please turn off the power in the main power supply box.
5. The range hood should use a specialized power socket with ground connection, because a middle connection, extension cord usage and multiple parameter wiring can cause electric shock, power socket overheating and fire. Please ensure that all operations are conducted by professional electricians and observe the corresponding national and local electrical regulations; Before connecting the cord, please turn off the power supply and take proper measures to prevent the power from automatically being connected.
6. If a gas stove needs to be moved before the range hood is installed, please turn off the main valve of the gas stove before moving the gas stove.
7. The wall on which the range hood is installed should be strong enough.
8. In order to ensure safety and smooth installation, please use the standard accessories to install. When you install the expansion tube, please ensure a tight fit between the expansion and the hole on the wall. Please do not drill a hole which is too large in case of the expansion tube becoming loose and accidental falling.
9. Please run gas exhaust outdoors to prevent fire.
10. Please do not exhaust the waste gas into the wall, attic or garage.
11. The waste gas from the range hood should not be exhausted into the hot smoke pipe that is used to exhaust smoke generated from burning gas or other fuel.
12. Please keep the machine horizontal from left to right.
13. After installation, confirm the range hood is qualified by running a test in which no abnormal phenomena occur.

Please read the manual carefully and keep the manual for future reference.

Installation Position

Figure 2 Cabinet Match Diagram
(a=24"-25 5/8"(610mm-650mm)(in USA)/ 25 5/8"-27 9/16"(650mm-700mm)(in Canada))

This range hood can only be installed in the kitchen; please do not use it in other places.

This range hood can only be installed above the stove, installation position is shown in the figure.

Figure 3 Installation Diagram
(a=24"-25 5/8"(610mm-650mm)(in USA)/ 25 5/8"-27 9/16"(650mm-700mm)(in Canada))

The room temperature should not exceed 40°C.

The installation wall should be of an incombustible substance; installing the machine on wooden material or other combustible material is prohibited.

Calculation before installation
Please refer to the figure below for accurate calculation before installation.

Installation Diagram of the Range Hood
Hole dimension of the upper cabinet or suspended ceiling:

Notes:

1. Reserved dimension between the cabinet and the machine is recommended as ≥1/4 '' (5mm) (see the figure);
2. 27''-38 5/8''(685-980mm) in the cabinet match diagram is the dimension range, including trim cover height.
3. Installation height of the range hood is a recommended value; the cabinet and range hood match diagram is only for reference.
4. You may need to allow for a gap between the upper side of the range hood and the bottom of the cabinet to install and disassemble, please pay attention.

Preparations before installation

To avoid damaging the range hood, please ensure that no debris get into the air outlet.

• Estimate outlet pipe position that connects the range hood to the outside, please refer to the installation diagram.
• A linear and short air outlet allows the range hood to exhaust smoke more smoothly.
• Avoid using an outlet pipe which is too long or has too many corners since this kind of pipe will affect the smoke exhausting effect.
• Please use duct tape to seal the connection between the outlet pipe and the wall holes. Please ensure a tight connection between the outlet and the outlet housing.
• An undersized hole will affect the smoke exhausting effect; it is recommended to broaden the hole to 6" on the premise of ensuring safety.

Four installation requirements

1. The installation height of the range hood (i.e. the distance between the supporting surface of the cooking appliance on the range and the lowest part of the range hood) is 24"25 5/8"(610mm~650mm)(in USA)/25 5/8"27 9/16"(650mm~700mm)(in Canada). The installation height is the recommended value, and the cupboard and the range hood shown in the figure is for reference only. When the installation height of this product (i.e. the distance between the supporting surface of the cooking appliance on the range and the lowest part of the range hood) is lower than 24"(610mm)(in USA)/25 5/8"(650mm) (in Canada), all parts below 24"(610mm)(in USA)/25 5/8"(650mm)(in Canada) are nonflammable parts of the range hood or parts working under safe and ultra-low voltage, and the deformation of these parts will not affect the protection against the touch of live parts. (If relevant laws in the region stipulate the installation height of range hood, it is recommended to abide by relevant laws, but the oil smoke suction effect of the product may be affected to some extent.)
2. Air outlet pipe should reach outdoors, interfaces should be sealed well;
3. In order to ensure proper smoke exhausting effect, the exit of the outlet pipe should not be deformed in case of decreasing supply area.
4. Power socket should be connected to the ground grid. Power cord has a total length of 1.3m, please take this into consideration when design the power socket position.

The waste gas from the range hood should not be exhausted into the hot smoke pipe that is used to exhaust smoke generated from burning gas or other fuels.

Installation Procedures

1. Determine the space for installing the hood above the cooktop, which shall meet the hood installation height.
2. Use an ultrasonic stud detector to find the wooden board behind the wall and mark it.
3. Determine the center point of the cooker and use the horizontal ruler to draw the vertical centerline of the range hood installation.
4. Determine the installation height of the range hood, 25 5/8"-27 9/16" (650mm-700mm), with a base point at the cooker holder, and draw a baseline with a horizontal ruler.
5. Determine the position of the machine hook, 21 5/8" (548.5mm), based on the range hood installation height line. Confirm that the trim cover is in the position of the trim cover hook according to the actual installation environment (up to 15 3/4" (400mm) above the machine hook reference line). Draw a reference line with a horizontal ruler.
6. Unpack box and take out the machine hook and the trim cover hook, and mark the fixing holes for the machine hook and the trim cover hook according to the marked position.
7. Drill holes with a diameter of 7/16'' (10 mm) and a depth of 2 3/8'' (60 mm) at the marked points with an impact driver. If the hole is marked over a wooden stud, you just need to get through the surface of the wall. Note: If there is no wooden stud at point of the machine hook, please drill holes in the wall behind the hook, insert and fix a wooden board and wooden stake, and affix the machine hook to the reinforced wooden board. The wooden board must be reinforced and reliable, able to bear a weight of 60 kg.
8. Take the expansion tube and wood screws out of the accessory bag, insert the expansion tube into the hole on the wall and fix the hook with wood screws. If there is just a wooden stake, affix it directly with wood screws.
   Note: Keep the hook horizontal with a horizontal ruler.
9. Two people take out the complete machine from the packing box, unscrew the four screws which fix the fan cover to the back of the range hood, and remove the fan cover and the trim cover. Screw two of the screws from inside outside to the top screw hole at the outer cover. Do not screw too tightly, leave a distance of 3mm
10. Unwrap the fan packaging, place the outlet housing and sealing gasket on the air outlet of the range hood and fix the outlet housing and air outlet with 8 M4×12 screws.
11. Using two people, hang the range hood on the machine hook and use the horizontal ruler to keep it horizontal. Fix the range hood and the main machine hook with a M4*8 screw as shown in Figure 4.
    
12. Put the pre-arranged smoke pipe on the outlet housing, fix the outlet pipe and the outlet housing on both the left and right sides with 2.9×19 screws. Then seal the outlet pipe and the outlet housing with aluminum foil tape. Plug the power supply of the range hood into the socket, then turn on the fan to check if there is any air leakage.
    
13. Remove the protective film of the fan cover and the trim cover, put the trim cover into the fan cover, reaching out a distance of about 2'' (50mm). Pick up the fan cover and the trim cover and hang the trim cover on the trim cover hook. Then slowly push it to the right place, then slowly put the fan cover down into the exhaust fume collecting hood.
14. Remove the protective film of the exhaust fume collecting hood, remove the oil cup protective film and hang the oil cup. Press the cleaning button and after the lifting rod is lowered down, install the outer net of the air inlet. Then remove the protective film of the wing-like plate and install it.
15. Finally, attach the corner bumpers, which help avoid head collisions, on the hood corners as shown in (Figure 6). Clean fingerprints from the surface of the range hood. Installation is complete.
    

Explosive View

Documents / Resources

References

• Range Hoods, Cooktops, Ovens | FOTILE

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download FOTILE EMG9030 - Wall Mount Range Hood with Touchscreen in Stainless Steel Manual