WINIX ZERO-N (AZNU230-HWE) - Air Purifier Manual

• Please read and follow all safety rules and instructions in this manual before operating.
• Please keep it in a safe place for future use.

▶ This product is suitable for 220 - 240V, 50/60Hz only.

3-STAGE AIR PURIFICATION

PACKAGE CONTENTS

CONTROLS

1. Fan Speed Indicator
   Indicates the current fan speed.
2. Change Filter Indicator
   LED light indicates when it is time to change the filter.
3. Reset Button
   After replacing a filter, press the RESET button for at least 5 seconds.
4. Air Quality Indicator
   Color-coded LED indicates one of three levels of air quality.
5. Power Button
   Turns the unit on or off.
6. Fan Speed Button (UP/DOWN)
   Enables Manual operation of the unit. Press to cycle through and set the desired fan speed (Low, Medium, High).
7. Light Sensor
   Detects the amount of ambient light within the environment, to adjust the brightness of the LED indicators.

WHERE TO USE

Allow 30 - 45 cm. of space between TVs, radios, and other electronic products electromagnetic interference from certain electronics may cause product malfunction.

Place indoors away from direct sun light direct exposure may cause product malfunction or failure.

Only place on hard, flat surfaces flimsy or slanted surfaces may result in abnormal noise and vibrations.

Follow these instructions to reduce the risk of serious injury or death and to reduce risk of damaging the unit.

※ This unit is not intended to be used to preserve documents or in art conservation.

INSTALLING FILTERS

This product comes with all required filters. The protective plastic wrap must be removed from the filter before use.

※ Operating the unit without removing the plastic wrap may result in product failure.

※ Unplug and make sure the unit is turned off before installing filter.

1. Remove the front panel by pressing down on both edges of the front and gently pulling it toward the front.
   
2. Press on the Pre-filter tabs near the top of the filter, release and remove.
   
3. Remove the carbon filter from the filter case.
   
4. Remove filters from protective plastic wrap.
   
   • Operating the unit without removing filters from plastic wrap may cause abnormal noise, deformation, or fire as a result of overheating.
5. After removing the packing vinyl of the filter, insert the carbon filter into the filter case.
   
6. Pull out the True HEPA filter.
   
7. Remove the filter case, then remove the True HEPA filter.
   
8. True HEPA filter → Filter case in order, pushing it in close to the back of the product.
   
9. After inserting both ends of the fabric pre filter, press both sides of the top to close it.
   
10. Remove the fabric pre filter that is fastened to the front panel.
    
    • The fabric pre filter is secured by the 12 hooks on the back of the front panel.

When to service and replace filter

Filter	Indicator Light	When to service	When to replace
Fabric filter	none	Clean once every 14 days	Permanent
Carbon filter	none	Can NOT be WASHED	Replace every 3 months
True HEPA filter			Lasts up to 6~12 months

※ Intervals between filter replacement may vary depending on environment.

※ For optimal use, Fabric filter can be cleaned once every 14 days which can extend the life of other filters.

To purchase replacement Winix filters

contact your local dealer

Filter R:
Carbon filter and True HEPA filter

SAFETY AND CAUTIONS

Before operating this equipment, carefully read and follow these safety cautions

Ensure filters are inserted before running unit
running unit without filters can shorten the units life and cause electric shock or injury.

Be sure foreign objects are NOT inserted into the vents on the unit
objects can include pins, rods, and coins.

Do not touch any part of the interior of the unit with wet hands
the high voltage may cause electric shock.

Ensure unit intake and outlet vents do not become blocked
blockage may lead to increased internal temperatures causing product failure and deformation.

Do not use the unit as a step stool or place heavy objects on it
personal injury may occur or product failure and deformation.

Follow these instructions to reduce the risk of serious injury or death and to reduce risk of damaging the unit.

INITIAL OPERATION

1. Insert the power cord into an electrical outlet.
   
2. Press the 'Power' button.
   

   NOTE	During the first 30 seconds of power up, the Air Quality Indicator will cycle through Blue, Amber and Red colors. The Particle Sensors take approximately 30 seconds to gauge the air quality in the environment, after which normal operation will begin.

3. By default, when the unit first powers on, the mode will be set to Auto enabled.
   
   • When in Auto mode, the fan speed will be automatically adjusted according to the environments air quality.

NOTE	In Auto mode, as the indoor air quality improves, the fan speed will automatically be reduced to Low. When the unit is running, you may hear a chirping or buzzing sound.

AUTO & SLEEP

Auto Mode

Enables auto operation based on the unit's air quality Particle Sensor.

1. Press the Fan speed (UP/DOWN) button to select Auto mode.
   
   • The LED 'Auto' light will indicate when Auto mode is activated, and operation will begin.

NOTE	When in Auto mode the fan speed is automatically adjusted according to the indoor air quality. As the indoor air quality improves, the fan speed will automatically be reduced. If the indoor air quality decreases, the fan speed will automatically increase.

Sleep Mode

1. Press the Fan speed (UP/DOWN) button to select Sleep mode.
   
   • The LED 'Sleep' light will indicate when Sleep mode is activated, and operation will begin.

NOTE	When Sleep mode is selected, the fan speed is automatically set to Low. The fan speed can be manually changed by pressing the Fan Speed button, changing the unit into manual mode. When Sleep Mode is activated, the Air Quality Indicator LED light is disabled.

MANUAL & AIR QUALITY INDICATOR

Manual Mode (setting fan speed)

Users can optative to manually set the fan speed to Low, Medium, High.

1. Press the Fan Speed button to set the desired fan speed.
   

NOTE	When Manual Mode is selected, Auto Mode is automatically disabled.

Air Quality Indicator

When on, the LED light will indicate the current indoor air quality according to three levels: BLUE (good), AMBER (fair), RED (poor).

NOTE	Air quality level is displayed on the indicator, based on the Particle Sensors. Depending on the immediate environment, the indicator may change frequently in color or stay the same for lengthy periods of time.

FILTER CARE

About The Filters

When the Check Filter indicator LED is on, it is time to replace the True HEPA filter.

Filter	Indicator Light	When to service	When to replace
Fabric filter	none	Clean once every 14 days	Permanent
Carbon filter	none	Can NOT be WASHED	Replace every 3 months
True HEPA filter			Lasts up to 6~12 months

※ Intervals between filter replacement may vary depending on environment.

※ For optimal use, Fabric filter can be cleaned once every 14 days which can extend the life of other filters.

To purchase replacement Winix filters

contact your local dealer

Filter R:
Carbon filter and True HEPA filter

NOTE

The lifetime of a Filter is depending on the level of pollutants in the air. The more dust present in the environment, the more dust accumulates in the filters, shortening the life. If the filters are heavily soiled or have a bad odour, or if the fan strength is significantly weakened, replace filters even if the Change Filter indicator has not yet turned on.

Resetting The Unit

1. After replacing the filters, turn the power back on and then use a thin object, such as a paper clip, to press the RESET switch for 5 seconds.
   

Cleaning the Fabric Pre-filter

Intervals between filter cleaning may vary depending on the air quality.

1. Use a vacuum cleaner or soft brush to clean the Fabric filter. If it is excessively soiled, rinse in room temperature water.
   
   • Do not use detergent or soap.
   • Allow the filter to dry for 24 hours or more before using

※ If the Fabric Pre-filter becomes damaged or in any way needs replacement: Please contact your local dealer

NOTICE

Do not use benzene, alcohol, or other volatile fluids, which may cause damage or discoloration. The Fabric Pre-filter is reusable after cleaning, ensuring it is completely dry. Do not use hot water over 40oC or volatile fluids such as paint thinner. After washing the filter, allow it to dry completely in a well ventilated area. Otherwise, it may develop a bad odour.

PARTICLE SENSOR CARE

Particle Sensors Care

For optimal performance of the Particle Sensor, which detects airborne dust and ultrafine particles, clean it every two months. Clean it more frequently when the unit is running in a place with high dust levels.

1. Open the Particle Sensor cover.
   
2. Use a damp cotton swab to wipe the lens and intake area of the Particle Sensor.
   
   • To clean the sensor area, use only water. Do not use volatile substances such as alcohol or acetone
3. Wipe away any remaining moisture with a dry cotton swab.
   
4. Close the Particle Sensor cover.
   
   • The Particle Sensors cover may be cleaned using a vacuum cleaner

CLEANING CARE

Cleaning the Exterior & Interior

1. Wipe with a soft damp cloth using room temperature water. Afterwards, wipe it down with a clean dry cloth.
   
   • To keep unit in peak condition, clean every 1-2 months.
2. Open the front panel and clean the interior with a vacuum cleaner.
   
   • For optimal performance, clean every 1-2 months.

NOTICE

When cleaning the unit, always unplug the power cord first and then wait until the unit has cooled down. Never disassemble, repair, or modify this unit yourself. Do not use flammable sprays or liquid detergents. Do not allow children to clean or maintain the unit. Before cleaning or maintaining, ensure unit is unplugged.

FREQUENTLY ASKED QUESTIONS

UNIT SPECIFICATIONS

※ The exterior, design and product specifications may be changed without prior notice to improve product performance.

Contact your local dealer for product related inquiries and customer service

WWW.WINIX.COM/EU