Advertisement
NOTE: When assembling your HydroVac, there may be a little water in or around the water tanks. This is because we test all our HydroVacs before you buy them to ensure the highest quality.
NOTE: To remove the handle, press the release button located on the back of the unit with a thin tool while pulling up on the handle.
Prior to first use, charge the battery completely. A full charge takes approximately 4 hours.
LED BATTERY POWER AND CHARGING INDICATOR
Charging | |
Low Charge | |
Mid Charge | |
Nearly Full | |
Full Charge Note: Full Charge takes approximately 4 hours. | |
In Use | |
Full Charge | |
Mid Charge | |
Nearly Empty (Pulsing) | |
No Charge |
NOTE: The Shark battery, like all lithium-ion batteries, will naturally decrease in capacity over time from the 100% capacity of a new battery.
Charge the unit by placing it on the dock. Make sure the contacts on the body are aligned with the contacts on the charging dock.
The Battery Icon on the main body will illuminate when charging begins.
When charging is complete and you need to use the unit again, lift it off the dock.
NOTE: When docked properly, the charging lights on the Main Body will blink, indicating that charging has begun. When charging is complete, all three indicator lights will turn off.
NOTE: The main unit comes with a partial charge. For maximum runtime, charge fully before first use (approximately 4 hours). Leaving the unit charging will not damage battery life.
Press the release button and lift off the Clean Solution Tank.
Unscrew the cap and add water to the tank, up to the WATER line. Next, add Shark HydroVac Multi-Surface Concentrate, filling to the HYDROVAC CONCENTRATE line. Replace the cap and reinsert the tank until it clicks into place. The top of the tank should be flush with the top of the body.
NOTE: Only use Shark HydroVac Multi-Surface Concentrate, Shark HydroVac Disinfectant, and water with this product.
NOTE: Be sure to not overfill the Clean Solution Tank with more HydroVac Multi Surface Concentrate than instructed, as this may clause streaking.
NOTE: Without sufficient water supply in the clean solution tank, HydroVac will not run.
Press and release the Power button on the handle to turn on power. To turn off power, press the button again.
Use Hard Floor mode for powerful cleaning on bare floors. To activate Hard Floor mode, turn on the unit and tilt the handle back.
To clean area rugs, press the Area Rug icon on top of the handle. The Area Rug light on the main body will illuminate. To turn off Area Rug mode (and to switch back to Hard Floor Mode), press the button again.
NOTE: To prevent leakage, DO NOT place the main body on the floor. The nozzle should always be kept flat on the floor.
NOTE: If you encounter a difficult stain, use Area Rug Mode for improved stain cleaning.
NOTE: If you encounter a stubborn odor on your floor or area rug, continue to clean in Area Rug mode until the odor is gone.
NOTE: If your floors are cloudy, streaky, or spotty after cleaning, it may be due to accumulated soap or grease residue. The floor may require several cleanings with the Hydrovac.
The self-clean cycle automatically cleans the system and the brushroll.
Recommended after every use
See LED Glossary for more information on indicator lights during self-clean cycle.
NOTE: Make sure the clean solution tank is at least half full and that the dirty water tank is empty before running the selfclean cycle.
You can clean the brushroll by hand as an alternative to the self-clean cycle, and to remove debris or hair wrapped around the brushroll.
NOTE: Do not place brushroll in washing machine or dishwasher. Replace the brushroll after 6 months.
NOTE: Replace the filter every 6 Months.
NOTE: Do not place dirty water tank in washing machine or dishwasher.
If you run over a hard or sharp object or notice a noise change while using your unit, check for blockages or objects caught in the brushroll, nozzle chamber, or inlet hose.
Replace the filter and brushroll every 6 months.
Only use Shark HydroVac Disinfectant, Shark HydroVac Concentrates, or water with the Shark HydroVac.
To order brushrolls, filters, Shark HydroVac Multi-Surface Concentrate, and Shark HydroVac Disinfectant, please visit sharkclean.com or scan the QR code below.
SCENARIO SCENARIO | VISUAL | DETAILS |
UNIT IS IN USE | ||
Single battery icon is on. | Solid. | Battery low. Note - you will not be able to run a self-clean cycle. |
Self-clean icon is pulsing. | Pulsing | Place unit on dock while self-clean icon is pulsing. Press the power button to run |
Single battery icon is pulsing. | Pulsing | Battery is close to running out. |
Self-clean icon has turned off. | Off | Insufficient battery life to run self-clean cycle after use. |
UNIT IS IN PLACED ON THE DOCK | ||
Battery icons are pulsing. | Pulsing | Unit is charging. |
Self-clean icon is on. | On | There is sufficient battery life to run a self-clean cycle. Press the power button to run a self-clean cycle. |
Self-clean icon is off. | Off | There is not sufficient battery life to run self-clean cycle. Wait until self-clean icon turns on to run a self-clean cycle. |
Power button is pressed to activate self-clean cycle. Battery Icons and Self-clean clean icon flash three times. | Flash ×3 | Unit is charging. There is not sufficient battery life to run a self-clean cycle. Wait until Self-clean icon turns on to run a Self-clean cycle |
Power button is pressed to activate self-clean cycle. Self-clean icon is pulsing. | Pulsing | Self-clean cycle is running. Self-clean icon will turn off when cycle is complete. Battery icons will turn on and unit will begin charging |
SELF-CLEAN CYCLE IS IN PROCESS; SELF-CLEAN CYCLE PAUSES | ||
Self-clean icon is flashing Self-clean icon is flashing. Blue water droplet icon is flashing. Blue water droplet icon is flashing. | Flashing | Clean solution tank is empty. Fill clean solution tank and press the power button to resume Self-clean cycle. |
Self-clean icon is flashing Self-clean icon is flashing. Red water droplet icon is flashing. Red water droplet icon is flashing. | Flashing | Dirty water tank is full. Empty Dirty water tank and press the Power button to resume self-clean cycle. |
UNIT IS IN USE; CLEANING FUNCTIONS TURN OFF | ||
Blue water droplet icon is flashing. | Flashing | Clean solution tank is empty. Fill clean solution tank, press the power button to resume cleaning. |
Red water droplet icon is flashing. | Flashing | Dirty water tank is full. Empty dirty water tank. Press the power button, resume cleaning. *If this is a false error, remove the solids separator and clean completely. Allow part to dry for 24 hours or dry manually. |
Red water droplet icon is flashing. Red area rug icon is flashing. | Flashing | Brushroll cover has been removed. Attach brushroll cover. Press the power button to resume cleaning. |
Red water droplet icon is flashing. Red area rug icon is flashing. | Flashing out of sync | Brushroll is jammed. Remove brushroll cover and brushroll. Remove any object that may be causing the brushroll to jam. Press the power button resume cleaning. |
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Shark HydroVac WD200 - Cordless 3-in-1 Cleaner Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the HydroVac WD200 that isn't answered in the manual? Leave your question here.