Advertisement
For proper operation, ensure all parts are firmly clicked into place.
For cord access, rotate upper hook down and remove cord.
Use cord clip located on the side of wand to hold cord in place while vacuuming.
Select surface setting:
O Power Off
I Hard Floor
For bare floors and small area rugs.
II Carpet
For carpets.
Your Suction Control slider located on the top of the handle allows you to adjust your suction depending on your floor type.
MIN: to reduce suction and increase maneuverability on carpets.
MAX: to increase suction on bare floors.
WHAT DOES THE BRUSHROLL INDICATOR LIGHT MEAN?
Solid Green: The brushroll is spinning and working as it should.
Solid Red: There is a jam in the brushroll area. Turn your vacuum off, unplug from the wall and remove any blockages in the nozzle.
Flashing Red: The motorized floor nozzle is overheating. Turn your vacuum off and wait a minimum of 45 minutes for it to cool down.
NOTE: For deep carpet cleaning per ASTM F608 (embedded dirt in carpets), set to MAX suction and use setting II, Carpet.
To engage brushroll, place foot on floor nozzle and tilt handle back.
Press the Handle Release button to detach the handle from the wand.
Press the Wand Release button to detach the wand from the pod.
NOTE: All accessories are compatible with both the wand and the handle.
Unplug the power cord before performing any maintenance.
To remove Dust Cup, press button on top of dust cup handle. Tilt dust cup forward, then lift to remove.
Press lower release button to open bottom of dust cup.
To remove collected debris from Lint Screen, press top release button and lift handle to open. Gently brush lint screen to clean.
To reinstall, place bottom of dust cup into pod and then tilt back until it clicks into place.
Regularly clean and replace your filters to keep your vacuum's suction power optimal.
To clean filters, rinse with cold water only to prevent damage from cleaning chemicals. Allow all filters to air-dry for at least 24 hours before reinstalling them to prevent liquid from being drawn into electric parts.
DO NOT use soap when cleaning the filters.
CLEAN PRE-MOTOR FILTERS EVERY 3 MONTHS
Remove Dust Cup, then lift out Filters.
CLEAN HEPA FILTER EVERY YEAR
Press down top of Filter Door. Tilt Filter Door and lift out. Press tab at top of HEPA Filter and pull away from the base of the vacuum. To reinstall, insert HEPA filter into unit and replace the filter door.
Follow the previous instructions for removing filters. The Pre-Motor Filter should be replaced every 2.5 years. The HEPA Filter should be replaced every 3 years.
Replacement Pre-Motor Foam & Felt Filter Kit
Replacement HEPA Filter
NOTE: To order replacement parts and filters, visit sharkaccessories.com.
Zero-M Technology
Shark's Zero-M™ self-cleaning brushroll delivers non-stop hair removal. If you run over a hard or sharp object or notice a noise change while vacuuming, check for blockages or objects caught in the brushroll.
NOTE: Do not be alarmed if there is visible hair wrap on the brushroll at any given time, as it should eventually make its way to the dust cup.
Using a coin, turn locks counterclockwise, then lift the door to access Brushroll.
Clean off any debris on the bristles.
NOTE: If any hair is wrapped around the brushroll, extending cleaning time will allow Zero-M technology to remove it for you. If some fibers remain wrapped around brushroll after continued use, carefully cut debris with scissors and remove from brushroll.
If you run over a hard or sharp object or notice a noise change while vacuuming, check for blockages or objects caught behind the brushroll.
Clear away any dust, dirt, or blockages in Debris Intake.
To close the cover, push down until it clicks into place, then close the locks with a coin.
Detach hose from vacuum pod, and check hose and opening on back of pod for blockages.
Detach wand from floor nozzle and handle, and check both ends for blockages.
Detach wand from power unit, lay unit down, and check opening for blockages.
Detach handle from wand and hose from the vacuum pod, and check openings for blockages.
Detach dust cup from vacuum pod. Empty dust cup, remove debris from lint screen, and check for blockages.
NOTE: Not all accessories come with all units. Please see the enclosed Quick Start Guide for your unit's configuration. To order additional accessories, visit sharkaccessories.com.
Vacuum is not picking up debris. No suction or light suction.
Vacuum lifts area rugs.
Brushroll does not spin in carpet cleaning mode.
Vacuum turns off on its own or indicator light flashes red.
This vacuum is equipped with a motor-protective thermostat. If your vacuum overheats, the thermostat will automatically turn the suction motor off. Perform the following steps to restart the thermostat:
For all other issues, please call Customer Service 1-800-798-7398.
Scan QR code using mobile device
Benefits of registering your product and creating an account:
Model Number:
Serial Number:
Date of Purchase:
(Keep receipt)
Store of Purchase:
TIP: You can find the model and serial numbers on the QR code label which is located on the bottom of the back of the vacuum pod.
Voltage: 120V, 60Hz
Watts: 1,150W
Amps: 9.5A
sharkclean.com
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Shark Navigator Pet Pro ZU60 - Upright Vacuum Aaspirateur Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the Navigator Pet Pro ZU60 that isn't answered in the manual? Leave your question here.